Description
C.A. Technologies Jaguar 100C — J100C-22-2467-401 (2.2mm Nozzle, 2467 Air Cap)
The C.A. Technologies Jaguar 100C J100C-22-2467-401 is a 2.2mm gravity feed conventional spray gun paired with the 21-2467 air cap — the heavy-viscosity step-up from the 1.8mm configurations for materials that restrict, spit, or produce an inconsistent pattern through a 1.8mm orifice. At 15 CFM and a 14" fan, this setup provides the orifice diameter and air volume needed to atomize high solid enamels, heavy body primers, adhesives, and other materials well over 30 sec. Zahn #2 that are too viscous for standard 1.8mm gravity gun setups. The 21-2467 cap is the dedicated air cap for the 2.2mm orifice — matched specifically to this orifice size by C.A. Technologies and the only standard cap option at 2.2mm in the J100C lineup. Used in marine fabrication, industrial coating operations, and specialty finishing environments where 2.2mm is the practical orifice before stepping to the 2.8mm gelcoat-specific configuration. Forged aluminum body, all stainless steel fluid passages, 700mL aluminum cup included. US made by C.A. Technologies in Louisville, CO. Call or text 586-210-0555 to confirm the right orifice for your material before ordering.
✓ 2.2mm stainless orifice — heavy materials that restrict at 1.8mm • ✓ Dedicated 21-2467 air cap — matched specifically to 2.2mm • ✓ 15 CFM • 14" max fan • ✓ Gravity feed — 700mL aluminum cup included • ✓ All stainless fluid passages • ✓ US Made — CET Verified
Model: J100C-22-2467-401 • Nozzle: 2.2mm (.086") • Air Cap: 21-2467 • Feed: GRAVITY • CFM: 15 @ 50 PSI
Cup: 51-401 700mL Aluminum (included) • Fan Control: 60-1500 (included) • Repair Kit: 10-105 • Max Inlet Pressure: 50 PSI • CET Verified Configuration
Overview
At a Glance
Specifications
Tech Specs
| Model | J100C-22-2467-401 |
| Fluid Nozzle | 31-0622 — 2.2mm (.086") 17-4PH Stainless |
| Air Cap | 21-2467 — Gravity, 15 CFM @ 50 PSI — dedicated 2.2mm cap |
| Needle | 40-1122 (122) — dedicated 2.2mm needle |
| Feed Type | GRAVITY — 700mL aluminum cup included, no pressure supply required |
| Gravity Cup Included | 51-401 700mL Aluminum — ships with gun |
| Max Inlet Pressure | 50 PSI |
| Air Consumption | 15 CFM @ 50 PSI — a compressor delivering at least 15 CFM sustained output is required for continuous finishing; a 5 HP two-stage or 7.5 HP single-stage compressor typically covers this. Heavy viscosity materials draw harder from the compressor than lighter coatings. For intermittent work with recovery time between passes, a smaller unit may be sufficient. Call or text 586-210-0555 to confirm your setup before ordering. |
| Max Pattern Width | 14" — widest fan in the J100C lineup alongside the 2268 cap |
| Air Inlet | 1/4" NPS (m) — standard shop air fitting |
| Fluid Inlet | 16mm x 1.5mm (m) — gravity cup threads directly onto gun |
| Body | Forged Aluminum — 20 oz., lightweight for all-day use |
| Fluid Passages | All Stainless Steel — chemical resistance to heavy body coatings, high solid enamels, and industrial primers |
| Fan Control | 60-1500 (included) — adjusts from full 14" fan down for targeted application |
| Repair Kit | 10-105 — all seals, o-rings, needle seal, springs for a complete rebuild |
| Fulfillment | Most in-stock orders ship same day — stocked at C.A. Technologies’ Colorado facility. Call or text 586-210-0555 to confirm availability. |
| Origin | US Made — C.A. Technologies (Louisville, CO) |
Application
CET Application Match — Best for This Setup
The CET Preferred Setup when 1.8mm has been confirmed as restrictive on your heavy material and you need a practical step up before the 2.8mm gelcoat configuration. Based on over 20 years supplying industrial finishing equipment, CET’s technical team recommends the J100C-22-2467-401 for industrial coating operations, marine fabrication shops, and specialty finishing environments running high solid enamels, heavy body primers, and adhesives that have shown restriction or inconsistent atomization through 1.8mm. The 21-2467 cap is C.A. Technologies’ own matched cap for this orifice — no guesswork in the air cap pairing.
Common Questions
Frequently Asked Questions
- When should I choose 2.2mm over 1.8mm?
- When your material restricts, spits, or produces inconsistent atomization through a 1.8mm orifice. The 2.2mm clears the passage restriction without requiring the full 2.8mm gelcoat setup. If you’re unsure, call or text 586-210-0555 — CET will confirm the right orifice for your material and viscosity.
- When should I choose 2.8mm over 2.2mm?
- Standard polyester gelcoat is viscous enough that C.A. Technologies specifically recommends the 2.8mm x 2268 configuration. If gelcoat is your primary material, step directly to the J100C-28-2268-401. The 2.2mm is better suited for heavy body primers, high solid enamels, and adhesives that restrict at 1.8mm but don’t require the full 2.8mm passage of a gelcoat setup.
- What compressor do I need for 15 CFM?
- A compressor delivering at least 15 CFM sustained output is required for continuous finishing — a 5 HP two-stage or 7.5 HP single-stage compressor typically covers this. Heavy materials draw harder from the compressor than lighter coatings at the same CFM. For intermittent work with recovery time between passes, a smaller unit may be sufficient. Call or text 586-210-0555 to confirm your specific setup before ordering.
- What needle does the 2.2mm nozzle use?
- The 40-1122 (122) needle assembly — dedicated to the 2.2mm orifice. Unlike the smaller orifice sizes where needles are shared across multiple orifice sizes, the 2.2mm has its own needle.
- What repair kit does the Jaguar 100C use?
- All J100C configurations use repair kit 10-105. CET stocks for same-day shipment — call or text 586-210-0555.
- Where can I find the full Jaguar 100C parts manual?
- The full parts manual is available on the Jaguar J100C Spare Parts page or via the download button below.
All Configurations
Find the Right Jaguar 100C for Your Application
The Jaguar 100C is available in 13 configurations covering 1.0mm through 2.8mm, with both stainless and carbide nozzle options. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Contact CET for a CET Application Match recommendation.
| Model | Nozzle | Air Cap | CFM | Fan | Best For | Order |
|---|---|---|---|---|---|---|
| J100C-10-2266-401 | 1.0mm | 21-2266 | 12 | 12" | Thin — lacquers, enamels, sealers | Order |
| J100C-12-2266-401 | 1.2mm | 21-2266 | 12 | 12" | Thin-medium — lacquers, enamels, primers | Order |
| J100C-13-2266-401 | 1.3mm | 21-2266 | 12 | 12" | Medium — lacquers, primers, enamels | Order |
| J100C-13-2466-401 | 1.3mm | 21-2466 | 15 | 13" | Medium — wider fan, higher CFM | Order |
| J100C-15-2266-401 | 1.5mm | 21-2266 | 12 | 12" | Medium — base coat, enamels, epoxies | Order |
| J100C-15-2366-401 | 1.5mm | 21-2366 | 12 | 10" | Medium — narrow fan, detail work | Order |
| J100C-15-2466-401 | 1.5mm | 21-2466 | 15 | 13" | Medium-heavy — enamels, urethanes, primers | Order |
| J100C-18-2266-401 | 1.8mm | 21-2266 | 12 | 12" | Medium-heavy — clear coat, epoxies | Order |
| J100C-18-2466-401 | 1.8mm | 21-2466 | 15 | 13" | Heavy — high solid coatings, gelcoat | Order |
| J100C-18-1590-401 | 1.8mm | 1590 | Low | — | Low CFM — sensitive substrates | Order |
| J100C-22-2467-401 | 2.2mm | 21-2467 | 15 | 14" | Heavy — heavy body primers, high solid enamels | Current |
| J100C-28-2268-401 | 2.8mm | 21-2268 | 15 | 14" | Ultra-heavy — gelcoat, C.A. Tech recommended | Order |
| J100C-28V-2268-401 | 2.8mm carbide | 21-2268 | 15 | 14" | Ultra-heavy — abrasive gelcoat, abrasive materials | Order |
Why Buy From CET
The CET Difference
- Over 20 years supplying industrial finishing equipment — CET has been matching customers to the right C.A. Technologies configuration since the beginning. We know these guns inside and out.
- Real technical support before and after the sale — call or text 586-210-0555 to reach CET’s technical team directly. We’ll confirm your nozzle, air cap, and setup before you order so you get it right the first time.
- Fast fulfillment on most in-stock orders — C.A. Technologies stocks these guns at their Colorado facility and most orders ship same day. Call or text 586-210-0555 to verify availability and confirm your ship date before ordering.
- Verified part compatibility — every configuration on this page is CET Verified. We stock the gun, the repair kit, the air caps, and the spare parts — so you’re never waiting on back-ordered components.
- Documentation included — every order ships with access to the full parts manual, air cap chart, and nozzle selection guide. No hunting for documentation after the sale.
- The best order fulfillment in the industry — you receive updates at every step of the process so you know exactly where your order is at all times. And in the rare case there’s a delay, we’ll let you know in advance — so you’re never chasing an order down again.
Why Choose the Jaguar 100C
Conventional Dependability Across Every Viscosity
The Jaguar 100C is C.A. Technologies’ workhorse conventional gravity feed gun — a forged aluminum body with all stainless steel fluid passages, nine air cap options, and nozzles from 1.0mm to 2.8mm covering the full spectrum from thin lacquers to ultra-heavy gelcoat in a single gun platform.
- All stainless steel fluid passages: Full chemical resistance to heavy body coatings, high solid enamels, and industrial primers — no corrosion or degradation over extended production use.
- Gravity feed simplicity: Cup threads directly onto the gun. No pressure pot, no hose management. Portable setup for operators moving around parts and workstations.
- Carbide nozzle options: Available at 2.8mm for abrasive or particle-laden materials that cause accelerated stainless nozzle wear.
- Forged aluminum body at 20 oz.: Lightweight enough for extended finishing sessions without operator fatigue building across a shift.
- 13 active configurations: From 1.0mm thin lacquers to 2.8mm ultra-heavy gelcoat, with both stainless and carbide nozzle options at the largest orifice size.
Gravity Cups & Accessories
Available Cups & Accessories
| Part # | Description | Notes |
|---|---|---|
| 51-401 | 700mL Aluminum Gravity Cup | Included with gun. Standard cup for most applications |
| 51-403 | 1000mL Aluminum Gravity Cup | Optional — larger capacity for extended heavy coating runs. Uses same 51-418 lid |
| 51-400 | 700mL Plastic Gravity Cup | Optional — lighter weight alternative |
| 51-418 | Gravity Cup Lid | For 51-401 and 51-403 aluminum cups |
| 52-300 | Mini Gun Regulator | Optional inline regulator for precise gun inlet pressure control |
| 51-432 | Magnetic Gravity Gun Stand | Optional — holds gun securely on metal surfaces between passes |
Jaguar 100C Product Manual
Full parts diagram, air cap chart, nozzle selection guide & replacement part numbers for all J100C configurations
Download the Jaguar 100C ManualNeed Help Confirming the Right Orifice for Your Material?
Call or text 586-210-0555 with your material type and viscosity. Based on over 20 years of industrial finishing equipment experience, CET’s technical team will confirm whether 2.2mm is the right step up from 1.8mm for your specific coating — or whether stepping directly to the 2.8mm gelcoat configuration makes more sense for your application.
