Description
Spray Gelcoat and Ultra-Heavy Coatings Without Restriction — C.A. Technologies Jaguar 100C J100C-28-2268-401 (2.8mm Nozzle, 2268 Air Cap)
The C.A. Technologies Jaguar 100C J100C-28-2268-401 is a 2.8mm gravity feed conventional spray gun paired with the 21-2268 air cap — C.A. Technologies’ own recommended configuration for gelcoat application, and the maximum orifice setup in the J100C lineup for ultra-heavy body coatings that restrict or spit through smaller nozzles. At 15 SCFM from a gravity cup, this configuration delivers the fluid volume that thick gelcoats, high solid enamels, and ultra-heavy body coatings require for clean atomization without the pressure supply infrastructure of a pressure feed gun. Used daily in marine fabrication, fiberglass shops, and industrial coating operations where gelcoat and heavy body material application is the primary task. The forged aluminum body carries all stainless steel fluid passages for full chemical resistance, and the gun ships with a 700mL aluminum gravity cup included. US made by C.A. Technologies in Louisville, CO. Call or text 586-210-0555 for setup guidance and availability before you order.
✓ 2.8mm stainless orifice — maximum in J100C lineup • ✓ C.A. Tech recommended for gelcoat • ✓ Gravity feed — 700mL aluminum cup included • ✓ 15 SCFM @ 50 PSI — 60-gallon compressor minimum • ✓ 14" max fan • ✓ US Made — CET Verified
Model: J100C-28-2268-401 • Nozzle: 2.8mm (.110") • Air Cap: 21-2268 • Feed: GRAVITY • SCFM: 15 @ 50 PSI
Cup: 51-401 700mL Aluminum (included) • Fan Control: 60-1500 (included) • Repair Kit: 10-105 • Max Inlet Pressure: 50 PSI • CET Verified Configuration
Overview
At a Glance
Specifications
Tech Specs
| Model | J100C-28-2268-401 |
| Fluid Nozzle | 31-0628 — 2.8mm (.110") 17-4PH Stainless |
| Air Cap | 21-2268 — Gravity, 15 SCFM @ 50 PSI |
| Needle | 40-1128 (128) — dedicated 2.8mm needle |
| Feed Type | GRAVITY — 700mL aluminum cup included, no separate pressure supply required |
| Gravity Cup Included | 51-401 700mL Aluminum — standard cup, ships with gun |
| Max Inlet Pressure | 50 PSI |
| Air Consumption | 15 SCFM @ 50 PSI — requires minimum 60-gallon compressor at 125 PSI rated output |
| Max Pattern Width | 14" — widest fan in the J100C 2.8mm lineup, suited for broad panel gelcoat coverage |
| Air Inlet | 1/4" NPS (m) — standard shop air fitting, most compressors connect directly |
| Fluid Inlet | 16mm x 1.5mm (m) — gravity cup threads directly onto gun, no hose assembly required |
| Body | Forged Aluminum — lightweight at 20 oz. for reduced sprayer fatigue on extended gelcoat applications |
| Fluid Passages | All Stainless Steel — full chemical resistance to gelcoat resins, polyester, and heavy industrial coatings |
| Fan Control | 60-1500 (included) — adjusts from full 14" fan down for targeted application on smaller panels |
| Repair Kit | 10-105 — all seals, o-rings, needle seal, springs for a complete rebuild |
| Fulfillment | Most in-stock orders ship same day — stocked at C.A. Technologies’ Colorado facility. Call or text 586-210-0555 to confirm availability. |
| Origin | US Made — C.A. Technologies (Louisville, CO) |
Application
CET Application Match — Best for This Setup
The CET Preferred Setup for gelcoat and ultra-heavy body coating application — C.A. Technologies’ own specified configuration for the J100C when spraying gelcoat. Based on over 20 years supplying industrial finishing equipment, CET’s technical team specifies the J100C-28-2268-401 for marine fabrication shops, fiberglass manufacturers, and industrial coating operations where gelcoat, polyester resins, and ultra-heavy body coatings are the primary daily material — materials that will spit, restrict, or produce an uneven spray pattern through any smaller orifice on a gravity feed gun.
Common Questions
Frequently Asked Questions
- Why does C.A. Technologies specifically recommend the 2.8mm x 2268 setup for gelcoat?
- Gelcoat is a polyester resin-based material with a viscosity that falls well above 30 sec. Zahn #2 — at the upper end of what most gravity guns are designed to handle. The 2.8mm orifice is the largest in the J100C lineup, giving gelcoat enough fluid passage to flow without restriction. The 21-2268 air cap is matched specifically to the 2.8mm nozzle to deliver the air volume and pattern needed for proper atomization. Using a smaller nozzle with gelcoat typically results in spitting, restricted flow, and an uneven spray pattern.
- What is the difference between J100C-28-2268-401 and J100C-28V-2268-401?
- Both use the 2.8mm orifice with the 21-2268 air cap at 15 SCFM. The only difference is the nozzle material — the standard J100C-28-2268-401 uses a 17-4PH stainless fluid nozzle (31-0628), while the J100C-28V-2268-401 uses a tungsten carbide nozzle that significantly extends service life when spraying abrasive or particle-laden gelcoat formulations. For standard gelcoat without abrasive additives, the stainless nozzle is the correct choice.
- What compressor do I need for 15 SCFM?
- 15 SCFM at 50 PSI operating pressure requires a minimum 60-gallon compressor rated at 125 PSI output. When spraying heavy viscosity materials like gelcoat, sustained spraying demands more from the compressor than lighter coatings at the same SCFM rating. An undersized compressor will pressure-drop during use, producing inconsistent atomization mid-panel. Call or text 586-210-0555 to confirm your compressor is sized correctly before ordering.
- Can I use a larger gravity cup for extended gelcoat runs?
- Yes — the 51-403 1000mL aluminum gravity cup is a direct upgrade from the included 700mL cup and uses the same 51-418 lid. The larger cup reduces refill interruptions during extended panel or mold gelcoat applications. Call or text 586-210-0555 to add it to your order.
- What repair kit does the Jaguar 100C use?
- All J100C configurations use repair kit 10-105, which includes all wear seals, o-rings, needle seal cartridge, and springs for a complete rebuild. CET stocks repair kits for same-day shipment — call or text 586-210-0555 to confirm availability.
- Where can I find the full Jaguar 100C parts manual?
- The full parts manual with exploded diagram, air cap chart, and nozzle selection guide is available on the Jaguar J100C Spare Parts page or via the download button below. CET includes documentation with every order.
All Configurations
Find the Right Jaguar 100C for Your Application
The Jaguar 100C is available in 13 configurations covering 1.0mm through 2.8mm, with both stainless and carbide nozzle options. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Contact CET for a CET Application Match recommendation.
| Model | Nozzle | Air Cap | SCFM | Fan | Best For | Order |
|---|---|---|---|---|---|---|
| J100C-10-2266-401 | 1.0mm | 21-2266 | 12 | 12" | Thin — lacquers, enamels, sealers | Order |
| J100C-12-2266-401 | 1.2mm | 21-2266 | 12 | 12" | Thin-medium — lacquers, enamels, primers | Order |
| J100C-13-2266-401 | 1.3mm | 21-2266 | 12 | 12" | Medium — lacquers, primers, enamels | Order |
| J100C-13-2466-401 | 1.3mm | 21-2466 | 15 | 13" | Medium — wider fan, higher SCFM | Order |
| J100C-15-2266-401 | 1.5mm | 21-2266 | 12 | 12" | Medium — base coat, enamels, epoxies | Order |
| J100C-15-2366-401 | 1.5mm | 21-2366 | 12 | 10" | Medium — narrow fan, detail work | Order |
| J100C-15-2466-401 | 1.5mm | 21-2466 | 15 | 13" | Medium-heavy — enamels, urethanes, primers | Order |
| J100C-18-2266-401 | 1.8mm | 21-2266 | 12 | 12" | Medium-heavy — clear coat, epoxies | Order |
| J100C-18-2466-401 | 1.8mm | 21-2466 | 15 | 13" | Heavy — high solid coatings, gelcoat | Order |
| J100C-18-1590-401 | 1.8mm | 1590 | Low | — | Low CFM — sensitive substrates, limited air supply | Order |
| J100C-22-2467-401 | 2.2mm | 21-2467 | 15 | 14" | Heavy — heavy body primers, high solid enamels | Order |
| J100C-28-2268-401 | 2.8mm | 21-2268 | 15 | 14" | Ultra-heavy — gelcoat, C.A. Tech recommended | Current |
| J100C-28V-2268-401 | 2.8mm carbide | 21-2268 | 15 | 14" | Ultra-heavy — abrasive gelcoat, abrasive materials | Order |
Why Buy From CET
The CET Difference
- Over 20 years supplying industrial finishing equipment — CET has been matching customers to the right C.A. Technologies configuration since the beginning. We know these guns inside and out.
- Real technical support before and after the sale — call or text 586-210-0555 to reach CET’s technical team directly. We’ll confirm your nozzle, air cap, and setup before you order so you get it right the first time.
- Fast fulfillment on most in-stock orders — C.A. Technologies stocks these guns at their Colorado facility and most orders ship same day. Call or text 586-210-0555 to verify availability and confirm your ship date before ordering.
- Verified part compatibility — every configuration on this page is CET Verified. We stock the gun, the repair kit, the air caps, and the spare parts — so you’re never waiting on back-ordered components.
- Documentation included — every order ships with access to the full parts manual, air cap chart, and nozzle selection guide. No hunting for documentation after the sale.
- The best order fulfillment in the industry — you receive updates at every step of the process so you know exactly where your order is at all times. And in the rare case there’s a delay, we’ll let you know in advance — so you’re never chasing an order down again.
Why Choose the Jaguar 100C
Conventional Dependability Across Every Viscosity
The Jaguar 100C is C.A. Technologies’ workhorse conventional gravity feed gun — a forged aluminum body with all stainless steel fluid passages, nine air cap options, and nozzles from 0.6mm to 2.8mm covering the full spectrum from very thin inks to ultra-heavy gelcoat in a single gun platform.
- All stainless steel fluid passages: Full chemical resistance to gelcoat resins, polyester, automotive coatings, and industrial topcoats — no corrosion or fluid passage degradation over extended production use.
- Carbide nozzle option at 2.8mm: The J100C-28V-2268-401 carbide variant is available for abrasive or particle-laden gelcoat formulations where stainless nozzle wear is a service life concern.
- Gravity feed — no pressure supply: Cup threads directly onto the gun. Portable, simple setup for operators moving around molds, panels, and parts. No hose management or pressure pot required.
- Forged aluminum body at 20 oz.: Lightweight enough for extended gelcoat application sessions without operator fatigue building up across a shift.
- 13 active configurations: From 1.0mm thin lacquers to 2.8mm ultra-heavy gelcoat, with both stainless and carbide nozzle options at the largest orifice sizes.
Gravity Cups & Accessories
Available Cups & Accessories
| Part # | Description | Notes |
|---|---|---|
| 51-401 | 700mL Aluminum Gravity Cup | Included with gun. Standard cup for most gelcoat applications |
| 51-403 | 1000mL Aluminum Gravity Cup | Optional upgrade — extended capacity for large panel or mold gelcoat runs without refilling. Uses same 51-418 lid |
| 51-400 | 700mL Plastic Gravity Cup | Optional — lighter weight, not recommended for gelcoat resins (check solvent compatibility) |
| 51-418 | Gravity Cup Lid | For 51-401 and 51-403 aluminum cups |
| 52-300 | Mini Gun Regulator | Optional inline regulator for precise gun inlet pressure control |
| 51-432 | Magnetic Gravity Gun Stand | Optional — holds gun securely on metal surfaces between passes |
Jaguar 100C Product Manual
Full parts diagram, air cap chart, nozzle selection guide & replacement part numbers for all J100C configurations
Download the Jaguar 100C ManualNeed Help Confirming This Is the Right Setup for Your Material?
Contact CET’s technical support team with your coating type and viscosity. Based on over 20 years of industrial finishing equipment experience, we’ll confirm whether the J100C-28-2268 is the right configuration — and whether stainless or carbide is the right nozzle for your specific gelcoat formulation. Call or text 586-210-0555.
