Description
C.A. Technologies Jaguar 100C — J100C-28V-2268-401 (2.8mm Carbide Nozzle, 2268 Air Cap)
The C.A. Technologies Jaguar 100C J100C-28V-2268-401 is a 2.8mm gravity feed conventional spray gun with a tungsten carbide nozzle paired with the 21-2268 air cap — the abrasion-resistant variant of the J100C-28-2268-401 for operators running abrasive or particle-laden materials that cause accelerated wear on stainless steel nozzles. The 2.8mm orifice and 21-2268 cap are identical to the standard stainless gelcoat setup — 15 CFM, 14" fan, C.A. Technologies’ own recommended configuration for ultra-heavy polyester gelcoat. The difference is the nozzle material: tungsten carbide holds its geometry significantly longer than stainless steel when abrasive particles or catalyzed gelcoat compounds pass through the orifice repeatedly over a production day. For operators whose stainless 2.8mm nozzle is wearing out faster than expected, the carbide nozzle is the correct solution. Forged aluminum body, all stainless steel fluid passages, 700mL aluminum cup included. US made by C.A. Technologies in Louisville, CO. Call or text 586-210-0555 to confirm this is the right setup for your material before ordering.
✓ 2.8mm tungsten carbide nozzle — abrasion-resistant for particle-laden & abrasive materials • ✓ 21-2268 air cap — C.A. Tech gelcoat-matched configuration • ✓ 15 CFM • 14" max fan • ✓ Gravity feed — 700mL aluminum cup included • ✓ All stainless fluid passages • ✓ US Made — CET Verified
Model: J100C-28V-2268-401 • Nozzle: 2.8mm Tungsten Carbide • Air Cap: 21-2268 • Feed: GRAVITY • CFM: 15 @ 50 PSI
Cup: 51-401 700mL Aluminum (included) • Fan Control: 60-1500 (included) • Repair Kit: 10-105 • Max Inlet Pressure: 50 PSI • CET Verified Configuration
Overview
At a Glance
Specifications
Tech Specs
| Model | J100C-28V-2268-401 |
| Fluid Nozzle | 31-0628 — 2.8mm Tungsten Carbide — abrasion-resistant for extended orifice life with abrasive materials |
| Air Cap | 21-2268 — Gravity, 15 CFM @ 50 PSI — same cap as standard stainless J100C-28-2268-401 |
| Needle | 40-1128 (128) — dedicated 2.8mm needle, same as standard stainless configuration |
| Feed Type | GRAVITY — 700mL aluminum cup included, no pressure supply required |
| Gravity Cup Included | 51-401 700mL Aluminum — ships with gun |
| Max Inlet Pressure | 50 PSI |
| Air Consumption | 15 CFM @ 50 PSI — a compressor delivering at least 15 CFM sustained output is required for continuous gelcoat finishing; a 5 HP two-stage or 7.5 HP single-stage compressor typically covers this. Ultra-heavy materials draw harder from the compressor than lighter coatings. For intermittent work with recovery time between passes, a smaller unit may be sufficient. Call or text 586-210-0555 to confirm your setup before ordering. |
| Max Pattern Width | 14" — widest fan in the J100C lineup, matched to the 2.8mm orifice for gelcoat coverage |
| Air Inlet | 1/4" NPS (m) — standard shop air fitting |
| Fluid Inlet | 16mm x 1.5mm (m) — gravity cup threads directly onto gun |
| Body | Forged Aluminum — 20 oz., lightweight for all-day use |
| Fluid Passages | All Stainless Steel — chemical resistance to gelcoat resins, abrasive coatings, and industrial topcoats |
| Fan Control | 60-1500 (included) — adjusts from full 14" fan down for targeted application |
| Repair Kit | 10-105 — all seals, o-rings, needle seal, springs for a complete rebuild |
| Fulfillment | Most in-stock orders ship same day — stocked at C.A. Technologies’ Colorado facility. Call or text 586-210-0555 to confirm availability. |
| Origin | US Made — C.A. Technologies (Louisville, CO) |
Application
CET Application Match — Best for This Setup
The CET Preferred Setup for operators running abrasive or particle-laden materials at 2.8mm where stainless nozzle wear is a recurring maintenance issue. Based on over 20 years supplying industrial finishing equipment, CET’s technical team specifies the J100C-28V-2268-401 when the standard stainless 2.8mm nozzle is wearing out faster than acceptable — typically in high-production gelcoat environments, abrasive aggregate spray applications, or when catalyzed materials with abrasive fillers are passing through the nozzle repeatedly over extended production shifts. The air cap, needle, and all other components are identical to the standard J100C-28-2268-401; only the nozzle material changes.
Common Questions
Frequently Asked Questions
- What is the difference between J100C-28V-2268-401 and J100C-28-2268-401?
- One thing only — the nozzle material. The 28V uses a tungsten carbide nozzle for abrasion resistance. The 28 uses a 17-4PH stainless nozzle. Air cap, needle, cup, repair kit, CFM, fan width, and all operating parameters are identical. If your stainless nozzle is holding up adequately in service, there’s no reason to choose the carbide version.
- How do I know if I need the carbide nozzle?
- If your stainless 2.8mm nozzle is wearing out in service — pattern starts to elongate or fluid delivery increases before you expect it to — the carbide nozzle is the right upgrade. If your stainless nozzle is holding up fine, stay with the standard J100C-28-2268-401. Call or text 586-210-0555 if you’re seeing wear issues and want CET to confirm the cause before upgrading.
- Can I upgrade my existing J100C-28-2268-401 to a carbide nozzle?
- Yes — the carbide nozzle (31-0628) is a direct replacement in the same gun body. You don’t need to purchase an entirely new gun to switch to carbide. Call or text 586-210-0555 to order the replacement nozzle.
- What compressor do I need for 15 CFM?
- A compressor delivering at least 15 CFM sustained output is required for continuous gelcoat finishing — a 5 HP two-stage or 7.5 HP single-stage compressor typically covers this. Ultra-heavy materials draw harder from the compressor than lighter coatings at the same CFM. For intermittent work with recovery time between passes, a smaller unit may be sufficient. Call or text 586-210-0555 to confirm your specific setup before ordering.
- What repair kit does the Jaguar 100C use?
- All J100C configurations use repair kit 10-105 — including the 28V carbide variant. CET stocks for same-day shipment — call or text 586-210-0555.
- Where can I find the full Jaguar 100C parts manual?
- The full parts manual is available on the Jaguar J100C Spare Parts page or via the download button below.
All Configurations
Find the Right Jaguar 100C for Your Application
The Jaguar 100C is available in 13 configurations covering 1.0mm through 2.8mm, with both stainless and carbide nozzle options. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Contact CET for a CET Application Match recommendation.
| Model | Nozzle | Air Cap | CFM | Fan | Best For | Order |
|---|---|---|---|---|---|---|
| J100C-10-2266-401 | 1.0mm | 21-2266 | 12 | 12" | Thin — lacquers, enamels, sealers | Order |
| J100C-12-2266-401 | 1.2mm | 21-2266 | 12 | 12" | Thin-medium — lacquers, enamels, primers | Order |
| J100C-13-2266-401 | 1.3mm | 21-2266 | 12 | 12" | Medium — lacquers, primers, enamels | Order |
| J100C-13-2466-401 | 1.3mm | 21-2466 | 15 | 13" | Medium — wider fan, higher CFM | Order |
| J100C-15-2266-401 | 1.5mm | 21-2266 | 12 | 12" | Medium — base coat, enamels, epoxies | Order |
| J100C-15-2366-401 | 1.5mm | 21-2366 | 12 | 10" | Medium — narrow fan, detail work | Order |
| J100C-15-2466-401 | 1.5mm | 21-2466 | 15 | 13" | Medium-heavy — enamels, urethanes, primers | Order |
| J100C-18-2266-401 | 1.8mm | 21-2266 | 12 | 12" | Medium-heavy — clear coat, epoxies | Order |
| J100C-18-2466-401 | 1.8mm | 21-2466 | 15 | 13" | Heavy — high solid coatings, gelcoat | Order |
| J100C-18-1590-401 | 1.8mm | 1590 | Low | — | Low CFM — sensitive substrates | Order |
| J100C-22-2467-401 | 2.2mm | 21-2467 | 15 | 14" | Heavy — heavy body primers, high solid enamels | Order |
| J100C-28-2268-401 | 2.8mm stainless | 21-2268 | 15 | 14" | Ultra-heavy — gelcoat, C.A. Tech recommended | Order |
| J100C-28V-2268-401 | 2.8mm carbide | 21-2268 | 15 | 14" | Ultra-heavy — abrasive gelcoat, abrasive materials | Current |
Why Buy From CET
The CET Difference
- Over 20 years supplying industrial finishing equipment — CET has been matching customers to the right C.A. Technologies configuration since the beginning. We know these guns inside and out.
- Real technical support before and after the sale — call or text 586-210-0555 to reach CET’s technical team directly. We’ll confirm whether carbide or stainless is right for your material before you order.
- Fast fulfillment on most in-stock orders — C.A. Technologies stocks these guns at their Colorado facility and most orders ship same day. Call or text 586-210-0555 to verify availability and confirm your ship date before ordering.
- Verified part compatibility — every configuration on this page is CET Verified. We stock the gun, the repair kit, the air caps, and the spare parts — so you’re never waiting on back-ordered components.
- Documentation included — every order ships with access to the full parts manual, air cap chart, and nozzle selection guide. No hunting for documentation after the sale.
- The best order fulfillment in the industry — you receive updates at every step of the process so you know exactly where your order is at all times. And in the rare case there’s a delay, we’ll let you know in advance — so you’re never chasing an order down again.
Why Choose the Jaguar 100C
Conventional Dependability Across Every Viscosity
The Jaguar 100C is C.A. Technologies’ workhorse conventional gravity feed gun — a forged aluminum body with all stainless steel fluid passages, nine air cap options, and nozzles from 1.0mm to 2.8mm covering the full spectrum from thin lacquers to ultra-heavy gelcoat in a single gun platform.
- Carbide nozzle at 2.8mm: The J100C-28V delivers extended orifice life in high-production gelcoat and abrasive material applications where stainless nozzle wear is a recurring maintenance issue.
- All stainless steel fluid passages: Full chemical resistance to gelcoat resins, abrasive coatings, and industrial topcoats throughout the gun body regardless of nozzle material.
- Gravity feed simplicity: Cup threads directly onto the gun. No pressure pot, no hose management. Portable setup for operators moving around molds and workstations.
- Forged aluminum body at 20 oz.: Lightweight enough for extended gelcoat sessions without operator fatigue building across a production shift.
- 13 active configurations: From 1.0mm thin lacquers to 2.8mm ultra-heavy gelcoat, with both stainless and carbide nozzle options at the largest orifice size.
Gravity Cups & Accessories
Available Cups & Accessories
| Part # | Description | Notes |
|---|---|---|
| 51-401 | 700mL Aluminum Gravity Cup | Included with gun. Standard cup for most applications |
| 51-403 | 1000mL Aluminum Gravity Cup | Optional — larger capacity for extended gelcoat runs. Uses same 51-418 lid |
| 51-400 | 700mL Plastic Gravity Cup | Optional — lighter weight alternative (confirm solvent compatibility with gelcoat) |
| 51-418 | Gravity Cup Lid | For 51-401 and 51-403 aluminum cups |
| 52-300 | Mini Gun Regulator | Optional inline regulator for precise gun inlet pressure control |
| 51-432 | Magnetic Gravity Gun Stand | Optional — holds gun securely on metal surfaces between passes |
Jaguar 100C Product Manual
Full parts diagram, air cap chart, nozzle selection guide & replacement part numbers for all J100C configurations including the carbide nozzle variant
Download the Jaguar 100C ManualNot Sure Whether You Need Carbide or Stainless?
Call or text 586-210-0555. Based on over 20 years of industrial finishing equipment experience, CET’s technical team will confirm whether your material and production volume warrant the carbide nozzle — or whether the standard stainless J100C-28-2268-401 is the right choice for your application.
