Description
This spray gun provides transfer efficiency in compliance with all regulations for air quality as an HVLP air spray gun and meets SCAQMD Rules for HVLP.
Constructed of a lightweight dropforged aluminum body and stainless steel fluid passages, the spray gun is designed to stand up under hard, continuous use. Ranges from 6 to 22 SCFM depending on operating pressure. A 1.5 to 5 horsepower air compressor is normally sufficient to supply atomizing air.
The MACH 1A also features independent control of atomizing and side port air, giving it an exceptionally high degree of atomizing capability with a wide range of coatings.
HVLP AIR NOZZLES
95P, 97P, 95AS, 95AP, 97AP, 905P ?ÿ
| GUN INLET PSI | NOZZLE AIR FLOW SCFM | NOZZLE ATOMIZING PSI |
| 20 | 11.0 | 3 |
| 30 | 15.7 | 5 |
| 38 | 17.5 | 7 |
| 45 | 19.6 | 9 |
| 50 | 22.5 | 10 |
HVLP AIR NOZZLE 93P ?ÿ
| GUN INLET PSI | NOZZLE AIR FLOW SCFM | NOZZLE ATOMIZING PSI |
| 8.0 | 5.5 | 3 |
| 11.5 | 7.0 | 5 |
| 14.5 | 8.0 | 7 |
| 17.0 | 9.5 | 9 |
| 18.0 | 10.0 | 10 |
HVLP AIR NOZZLE 94P ?ÿ
| GUN INLET PSI | NOZZLE AIR FLOW SCFM | NOZZLE ATOMIZING PSI |
| 14 | 7.0 | 3 |
| 21 | 9.0 | 5 |
| 27 | 11.0 | 7 |
| 30 | 12.0 | 9 |
| 33 | 13.0 | 10 |
HVLP AIR NOZZLE 90P ?ÿ
| GUN INLET PSI | NOZZLE AIR FLOW SCFM | NOZZLE ATOMIZING PSI |
| 5 | 4.0 | 3 |
| 7 | 4.5 | 5 |
| 10 | 5.0 | 7 |
| 12 | 5.5 | 9 |
| 15 | 6.0 | 10 |
HVLP AIR NOZZLE 92P ?ÿ
| GUN INLET PSI | NOZZLE AIR FLOW SCFM | NOZZLE ATOMIZING PSI |
| 6.0 | 4.5 | 3 |
| 8.5 | 6.0 | 5 |
| 11.0 | 6.8 | 7 |
| 13.5 | 7.5 | 9 |
| 15.0 | 8.0 | 10 |
HVLP AIR NOZZLE 100P ?ÿ
| GUN INLET PSI | NOZZLE AIR FLOW SCFM | NOZZLE ATOMIZING PSI |
| 3.0 | 3.2 | 2 |
| 6.1 | 4.8 | 4 |
| 9.0 | 6.0 | 6 |
| 11.6 | 6.9 | 8 |
| 14.3 | 8.0 | 10 |
FLUID NOZZLES STANDARD NOZZLES
|
MATERIAL |
FLUID NOZZLE NO. | APPLICABLE AIR NOZZLES | COMPATIBLE FLUID NEEDLE† |
| ULTRA LIGHT: Reduced Flow. | 89 (.020" Dia.) 89A (.025" Dia.) | 90P, 92P
93P, 94P 95P, 97P
95AP*
97AP* 100P | 47-478 |
| VERY LIGHT: Reduced Flow. | 90 (.030" Dia.) | 47-478 47-478 | |
| LIGHT: less than 15 to 20 seconds in a ZAHN 2 Cup, e.g., stains, varnishes, thin lacquers, automotive refinishing materials. | 91 (.040" Dia.) | ||
| 92 (.046" Dia.) | 47-478 | ||
| MEDIUM: 20 to 60 seconds in a ZAHN 2 Cup, e.g., general industrial coatings | 94 (.055" Dia.) 95 (.059" Dia.) 96 (.063" Dia.) | 47-478 | |
| HEAVY: greater than 60 seconds in a ZAHN 2 Cup. | 97 (.070" Dia.) | 47-478 |