Description
Complete Fine Finish Outfit, Ready to Spray — C.A. Technologies CAT-Xpress CAT Pack with Aluminum Cup (CAT-XPR-303R2)
The C.A. Technologies CAT-Xpress CAT-XPR-303R2 is a complete professional fine finish pressure feed spray outfit that includes everything needed to spray from day one — the CAT-Xpress gun, a 1QT aluminum pressure cup with regulator, both HVLP and pressure-reduced air caps, three nozzle and needle sets (0.8mm, 1.3mm, 1.8mm), and all tools in a carrying case. The aluminum pressure cup provides a proven, durable fluid supply for single-material runs and finishing operations where a reusable cup is preferred — no disposable liners required, straightforward solvent cleanup between jobs, and full compatibility with all solvent-based and waterborne materials the CAT-Xpress is designed to handle. At 9 CFM, the CAT-Xpress runs off a 30-gallon compressor minimum — one of the lowest air demands in the professional fine finish category — with precision engineered air caps that keep atomization particle size at the absolute finest. All stainless steel fluid passages, US made by C.A. Technologies in Louisville, CO. Call or text 586-210-0555 for nozzle selection guidance and availability before you order.
✓ 1QT aluminum pressure cup & regulator included • ✓ HVLP & pressure-reduced air caps included • ✓ 0.8mm, 1.3mm & 1.8mm nozzle/needle sets included • ✓ 9 CFM — 30-gallon compressor minimum • ✓ Complete ready-to-spray outfit • ✓ US Made — CET Verified
Model: CAT-XPR-303R2 • Kit Type: CAT Pack — 1QT Aluminum Cup • Feed: PRESSURE • Air Caps: HVLP (2403233) & Pressure-Reduced (2403218) • CFM: 9 @ 29 PSI
Nozzle Sets: 0.8mm, 1.3mm, 1.8mm (included) • Cup: 51-303-R2 1QT Aluminum • Repair Kit: 2411779 • CET Verified Configuration
Overview
At a Glance
Specifications
Tech Specs
| Model | CAT-XPR-303R2 (CAT Pack — 1QT Aluminum Cup) |
| Pressure Cup | 51-303-R2 1QT Aluminum — durable reusable cup for single-material and production finishing runs; solvent or water cleanup between jobs |
| Regulator | 52-5R2 — included; connects between air supply and cup for precise fluid pressure control |
| Air Caps Included | 2403218 Pressure-Reduced & 2403233 HVLP — both included, swap to meet compliance requirements |
| Nozzle/Needle Sets | 0.8mm (2404488/2397054), 1.3mm (2412850/2412848), 1.8mm (2404493/2397059) — all included |
| Feed Type | PRESSURE — pressurized through 52-5R2 regulator and 51-303-R2 aluminum cup |
| Max Gun Inlet Pressure | 29 PSI (pressure-reduced cap) / 26 PSI (HVLP cap) |
| Air Consumption | 9 CFM @ 29 PSI — requires minimum 30-gallon compressor at 90 PSI rated output; well within range of most single-phase shop compressors |
| Max Pattern Width | 13" pressure-reduced / 12" HVLP — handle-mounted quarter-turn fan adjustment during spraying |
| Fluid Tip Design | Thread-less construction — tool-free nozzle swap; faster changeover between material viscosities |
| Fan Control | Handle-mounted, quarter-turn — one-handed adjustment without stopping application |
| Air Adjustment Valve | Built-in at handle — immediate atomization adjustment at the gun without returning to the regulator |
| Fluid Passages | All Stainless Steel — chemical resistance to solvent-based and waterborne coatings, automotive finishes, and industrial topcoats |
| Repair Kit | 2411779 — all seals, o-rings, needle packing, and springs for a complete rebuild |
| Fulfillment | Most in-stock orders ship same day — stocked at C.A. Technologies’ Colorado facility. Call or text 586-210-0555 to confirm availability. |
| Origin | US Made — C.A. Technologies (Louisville, CO) |
Application
CET Application Match — Best for This Setup
The CET Preferred Setup for single-material production finishing where a complete ready-to-spray outfit with a proven aluminum pressure cup is the right tool — no disposable liners, no complex setup, just attach the cup, set the regulator, and spray. Based on over 20 years supplying industrial finishing equipment, CET’s technical team recommends the CAT-XPR-303R2 for automotive refinishing, woodworking, and industrial finishing operations that run the same material through the gun for an extended session and clean up with solvent between jobs — the aluminum cup provides a durable, straightforward fluid supply that holds up to daily production use and repeated solvent cleaning.
Common Questions
Frequently Asked Questions
- What is the difference between the CAT-XPR-303R2 and the CAT-XPR-PPSR2?
- Both kits include the same CAT-Xpress gun, both air caps, all three nozzle/needle sets, a regulator, and tools. The 303R2 uses a 1QT aluminum pressure cup — durable, reusable, clean with solvent between jobs. The PPSR2 uses a 3M PPS 2.0 disposable liner system — swap a liner between color changes instead of cleaning the cup. If you’re doing single-material runs or prefer a reusable cup, choose the 303R2. If you’re doing multi-color work, the PPSR2 saves significant cleanup time per shift.
- What compressor do I need for 9 CFM?
- 9 CFM at 29 PSI gun inlet requires a 30-gallon compressor at 90 PSI rated output — one of the lowest air demands in the professional fine finish category. Most single-phase shop compressors in the 25–60 gallon range handle the CAT-Xpress comfortably without constant pressure drop. Call or text 586-210-0555 if you’re running multiple guns off the same compressor.
- Does the CAT-Xpress meet HVLP compliance requirements?
- Yes — the included HVLP air cap (2403233) is designed for areas requiring HVLP compliance and operates at 26 PSI gun inlet. The pressure-reduced cap (2403218) at 29 PSI meets US pressure-reduced regulations. Both caps are included in the 303R2 kit. Check with your local regulator or facility compliance officer to confirm which cap requirement applies to your jurisdiction.
- What nozzle sizes are available beyond the three included?
- The CAT-Xpress fluid tip system covers 0.8mm through 2.2mm. Beyond the included 0.8mm, 1.3mm, and 1.8mm, additional sizes available include 1.0mm, 1.2mm, 1.4mm, 1.5mm, 2.0mm, and 2.2mm. For materials over 30 sec. Zahn #2 requiring 2.0mm or 2.2mm, the 2403224 or 2403235 air caps are also required. Call or text 586-210-0555 to confirm the right nozzle for your material.
- What repair kit does the CAT-Xpress use?
- The CAT-Xpress uses repair kit 2411779, which includes all wear seals, o-rings, needle packing assembly, and springs for a complete gun rebuild. CET stocks repair kits for same-day shipment — call or text 586-210-0555 to confirm availability.
- Where can I find the full CAT-Xpress parts manual?
- The full parts manual with exploded diagram, air cap chart, nozzle selection guide, and replacement part numbers is available via the download button below. CET includes documentation with every order.
Why Buy From CET
The CET Difference
- Over 20 years supplying industrial finishing equipment — CET has been matching customers to the right C.A. Technologies setup since the beginning. We know these guns inside and out.
- Real technical support before and after the sale — call or text 586-210-0555 to reach CET’s technical team directly. We’ll confirm your nozzle selection and whether the aluminum or PPS cup kit better fits your workflow.
- Fast fulfillment on most in-stock orders — C.A. Technologies stocks these guns at their Colorado facility and most orders ship same day. Call or text 586-210-0555 to verify availability and confirm your ship date before ordering.
- Verified part compatibility — every configuration on this page is CET Verified. We stock the gun, the repair kit, replacement nozzles, and air caps — so you’re never waiting on back-ordered components.
- Documentation included — every order ships with access to the full parts manual, nozzle chart, and air cap selection guide. No hunting for documentation after the sale.
- The best order fulfillment in the industry — you receive updates at every step of the process so you know exactly where your order is at all times. And in the rare case there’s a delay, we’ll let you know in advance — so you’re never chasing an order down again.
Why Choose the CAT-Xpress
Purpose-Built for Fine Finish Where Transfer Efficiency and Compliance Both Matter
The CAT-Xpress is C.A. Technologies’ answer to the fine finish operator who needs extreme atomization quality, HVLP and pressure-reduced compliance in the same gun, and ergonomics designed for all-day production use — without the air consumption demands of conventional spray guns.
- Precision engineered air caps: Both HVLP and pressure-reduced caps keep atomization particle size at the absolute finest — consistent finish quality across the full nozzle range.
- Thread-less fluid tip: Swap nozzle sizes without tools — faster changeover between materials during a shift and more consistent nozzle seating than threaded designs.
- Handle-mounted fan and air controls: Quarter-turn fan adjustment and built-in air valve at the handle means one-handed pattern and atomization adjustment without stopping application.
- All stainless steel fluid passages: Chemical resistance to solvent-based coatings, waterborne finishes, automotive materials, and industrial topcoats across all included nozzle sizes.
- 9 CFM total air consumption: Professional fine finish performance at less than half the air demand of conventional spray guns — practical for smaller shops and mobile setups without sacrificing atomization quality.
CAT-Xpress Product Manual
Full parts diagram, nozzle/air cap selection chart, application guide & replacement part numbers
Download the CAT-Xpress ManualNot Sure Which Kit or Nozzle Is Right for Your Application?
Contact CET’s technical support team with your material type, viscosity, and compliance requirements. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct nozzle, air cap, and kit configuration — and verify same-day availability. Call or text 586-210-0555.
