C.A. Technologies Panther 100G — P100G-13-2266-3T (1.3mm Nozzle, 2266-3T Air Cap)

The C.A. Technologies Panther 100G P100G-13-2266-3T is a 1.3mm PTFE coated conventional pressure feed spray gun paired with the 21-2266-3T air cap — delivering the highest SCFM and widest fan of any pressure cap in the P100G lineup at the 1.3mm orifice. At 16.2 SCFM and a 15" maximum fan under pressure, this setup atomizes medium viscosity adhesives, contact cements, and industrial coatings with strong air volume and PTFE non-stick cleanup built in. The 1.3mm orifice gives precise flow control for materials in the 21–28 second Zahn #2 range — more flow than 1.2mm, less than 1.5mm — making it the right choice when material viscosity sits right in the middle of medium. Used in cabinet shops, woodworking operations, and industrial finishing lines running medium adhesive and coating applications where PTFE cleanup advantage and wide fan coverage both matter. All stainless steel fluid passages. US made. Call or text 586-210-0555 for setup guidance and availability before you order.

Overview

At a Glance

• Configuration: 1.3mm stainless steel fluid nozzle + 21-2266-3T PTFE coated pressure air cap — CET Verified Configuration
• Best for: Medium adhesives, contact cements, epoxy primers, and industrial coatings in the 21–28 sec. Zahn #2 range
• Feed type: PRESSURE — 16.2 SCFM, 15" fan, PTFE coated air cap
• Air consumption: 16.2 SCFM @ 50 PSI max inlet
• Body: PTFE hard coat anodized forged aluminum — resists adhesive and coating buildup for fast cleanup
• Fluid passages: All stainless steel for full chemical resistance
• Fast fulfillment — most in-stock orders ship same day. Call or text 586-210-0555 to verify availability before you order.
• Origin: US Made by C.A. Technologies (Louisville, CO) — distributed by CET for over 20 years

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The P100G-13-2266-3T is a CET Preferred Setup when you need maximum fan width and the highest pressure SCFM at 1.3mm — with PTFE non-stick cleanup built in. Based on over 20 years supplying industrial finishing equipment, CET’s technical team specifies this configuration for cabinet shops and woodworking operations running medium contact cements, epoxy primers, and lacquers where the wider 15" fan covers panel and case goods surfaces efficiently and the PTFE coated air cap keeps cleanup fast after adhesive runs. It’s the top-spec pressure option at 1.3mm — when the 21-2263’s 14 SCFM and 14" fan are close but you need the extra air volume and fan width the 2266-3T provides.

• Cabinet and woodworking shops: 15" fan at 16.2 SCFM covers panel and case goods surfaces efficiently with medium adhesives and finish coatings
• Medium contact cements: 1.3mm orifice delivers controlled flow of medium viscosity formulations that over-apply through 1.5mm
• Epoxy primers and industrial coatings: All stainless steel fluid passages and PTFE body provide full chemical resistance and fast cleanup
• Production finishing lines: PTFE coated air cap maintains pattern consistency and reduces cleanup downtime between material changes

Common Questions

Frequently Asked Questions

What is the difference between the P100G-13-2266-3T and P100G-13-2263?

Both use the same 1.3mm fluid nozzle (31-0613). The 21-2266-3T runs at 16.2 SCFM with a PTFE coated air cap and a wider 15" fan. The 21-2263 runs at 14 SCFM with a standard aluminum air cap and a 14" fan. CET recommends the 2266-3T when PTFE non-stick cleanup is the priority for adhesive applications and you want the widest fan; the 2263 is the right choice when lower SCFM and a standard cap are preferred.

When should I choose 1.3mm over 1.2mm or 1.5mm?

The 1.3mm sits between the precision of 1.2mm and the heavier flow of 1.5mm. It’s the right choice when your material is a true medium viscosity — thin enough that 1.5mm over-deposits but thick enough that 1.2mm restricts flow or leaves an uneven pattern. Contact cements and epoxy primers in the 21–28 second Zahn #2 range are typical candidates. Not sure? Call or text CET at 586-210-0555.

Does the PTFE coating on the 21-2266-3T hold up to aggressive adhesives?

Yes — the PTFE hard coat is anodized into the aluminum, not a surface film. It provides durable, long-lasting non-stick performance through extended production use with contact cements, urethanes, and other aggressive adhesive formulations. Replacement air caps are available through CET when needed.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

What needle does the 1.3mm nozzle use?

The 1.3mm fluid nozzle (31-0613) uses the 40-1110 (110) needle assembly — shared with the 1.0mm and 1.2mm configurations. CET stocks replacement needles for same-day shipment.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Use the table below to find the right nozzle and air cap combination for your material, or contact CET for a CET Application Match recommendation.

PRESSURE requires pressurized fluid supply    SIPHON works with standard siphon cup    WATERBORNE anti-shear setup for waterborne adhesives

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

PTFE Coated Durability for Demanding Applications

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap. This matters most when spraying adhesives, contact cements, and other sticky or aggressive coatings that tend to foul standard aluminum gun bodies and air cap faces.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to surfaces, dramatically reducing cleaning time and extending component life.
• All stainless steel fluid passages: Full chemical resistance across solvent-based, waterborne, and aggressive adhesive formulations.
• Heavy duty needle spring: Maintains consistent trigger response and needle return under continuous production use.
• Forged aluminum body: Lightweight and durable — built for all-day production use without fatigue.
• 17 air cap options: From 0.6mm siphon to 2.8mm pressure — one platform covers the full range of coating viscosities.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.