C.A. Technologies Panther 100G — P100G-10-2266-3T (1.0mm Nozzle, 2266-3T Air Cap)

The C.A. Technologies Panther 100G P100G-10-2266-3T is a 1.0mm PTFE coated conventional pressure feed spray gun paired with the 21-2266-3T air cap — the smallest orifice configuration in the 2266-3T pressure lineup, designed for thin-to-medium adhesives, sealers, and light industrial coatings that benefit from the PTFE coated air cap’s non-stick surface and the high flow rate of 16.2 SCFM. Suited for operations spraying thin contact cement formulations, sealers, and light adhesive topcoats where precise flow control at a smaller orifice is needed alongside the easy cleanup advantage of the PTFE coated 2266-3T cap. The PTFE hard coat on both the gun body and air cap resists material buildup. All stainless steel fluid passages. US made. Call or text 586-210-0555 for setup guidance and availability before you order.

Overview

At a Glance

• Configuration: 1.0mm stainless steel fluid nozzle + 21-2266-3T PTFE coated pressure air cap — CET Verified Configuration
• Best for: Thin adhesives, sealers, contact cement formulations, and light industrial coatings in the 16–25 sec. Zahn #2 range
• Feed type: PRESSURE — consistent flow control at smaller orifice sizes
• Air consumption: 16.2 SCFM @ 50 PSI max inlet
• Body: PTFE hard coat anodized forged aluminum — resists adhesive and coating buildup for fast cleanup
• Fluid passages: All stainless steel for full chemical resistance
• Fast fulfillment — most in-stock orders ship same day. Call or text 586-210-0555 to verify availability before you order.
• Origin: US Made by C.A. Technologies (Louisville, CO) — distributed by CET for over 20 years

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The P100G-10-2266-3T is the CET Preferred Setup for operations spraying thin adhesive formulations, sealers, and light industrial coatings where the PTFE non-stick coating is needed for easy cleanup but material viscosity is low enough that a 1.0mm orifice provides better flow control than larger orifices. Based on over 20 years supplying industrial finishing equipment, CET’s technical team recommends this configuration for shops spraying thin contact cements, water-thin sealers, and light adhesive topcoats where a larger orifice would deliver too much material per trigger pull.

The 21-2266-3T at 16.2 SCFM delivers a wide 15" fan even through the 1.0mm orifice, giving excellent pattern coverage for thin materials. The PTFE coating on both the gun body and air cap makes this setup particularly practical for thin adhesive applications where cleanup frequency is high.

• Thin contact cements and adhesive sealers: 1.0mm orifice delivers precise, controlled flow of low-viscosity adhesive formulations
• Light industrial coatings and stains: High SCFM air cap atomizes thin materials cleanly into a wide fan for efficient coverage
• High-frequency cleanup applications: PTFE coated body and air cap make repeated cleanup between batches fast and practical
• Pressure feed precision: Consistent pressure-fed delivery at 1.0mm gives better flow control than siphon at thin viscosities

Common Questions

Frequently Asked Questions

Why choose a 1.0mm orifice for adhesives?

The 1.0mm orifice is the right choice when your adhesive or coating is thin — typically 16–25 seconds Zahn #2 — and a larger orifice would over-deliver material, causing runs, drips, or excessive adhesive buildup. Thin contact cements, adhesive sealers, and light formulations atomize better through a smaller orifice where material flow is more precisely controlled. Not sure if 1.0mm is right for your material? Call or text CET at 586-210-0555.

Why use the 21-2266-3T PTFE cap at 1.0mm instead of a smaller air cap?

The 21-2266-3T at 16.2 SCFM provides strong atomization energy even through the small 1.0mm orifice, delivering a full 15" fan pattern and clean breakup of thin materials. The PTFE coating on the air cap face is the key advantage for adhesive applications — it prevents material from bonding to the cap between passes, keeping the spray pattern consistent and cleanup fast.

What is the difference between the P100G-10-2266-3T and larger 2266-3T configurations?

All 2266-3T configurations share the same PTFE coated pressure air cap at 16.2 SCFM and 15" max fan. The difference is fluid orifice size: 1.0mm (this model) for thin materials, 1.2mm and 1.3mm for thin-to-medium, 1.5mm for medium-to-heavy, and 1.8mm for the thickest adhesives. CET can help match the right orifice to your specific material.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

Is pressure feed necessary at 1.0mm?

For thin materials a siphon setup can work, but pressure feed at 1.0mm gives more consistent, repeatable flow control — especially important when precise adhesive coverage is needed. The pressure supply ensures steady material delivery regardless of cup level, which matters in production environments.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Use the table below to find the right nozzle and air cap combination for your material, or contact CET for a CET Application Match recommendation.

PRESSURE requires pressurized fluid supply    SIPHON works with standard siphon cup    WATERBORNE anti-shear setup for waterborne adhesives

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

PTFE Coated Durability for Demanding Applications

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap. This matters most when spraying adhesives, contact cements, and other sticky or aggressive coatings that tend to foul standard aluminum gun bodies and air cap faces.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to surfaces, dramatically reducing cleaning time and extending component life.
• All stainless steel fluid passages: Full chemical resistance across solvent-based, waterborne, and aggressive adhesive formulations.
• Heavy duty needle spring: Maintains consistent trigger response and needle return under continuous production use.
• Forged aluminum body: Lightweight and durable — built for all-day production use without fatigue.
• 17 air cap options: From 0.6mm siphon to 2.8mm pressure — one platform covers the full range of coating viscosities.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.