C.A. Technologies Lynx 100C Conventional Spray Gun — 1.5mm / 21-2366 Siphon Setup (L100C-15-2366)

100 Series Conventional General Purpose | US Made

The Lynx 100C (L100C) is C.A. Technologies' high quality general purpose conventional spray gun, available in both pressure and siphon feed configurations. The L100C-15-2366 setup pairs the 31-0615 fluid nozzle (1.5mm) with the 21-2366 siphon air cap — delivering 12 CFM and a wide 14" pattern at 50 PSI. This is the medium-body siphon configuration to reach for when the 10" pattern of the 21-2266 is too narrow for your application but you don't need the higher air draw of the 21-2466.

At a Glance

• Feed type: Siphon feed
• Best material types: Medium body enamels, urethanes, epoxy primers, and sealers at moderate viscosity — materials that flow freely through a 1.5mm tip from a siphon cup
• Air use: 12 CFM @ 50 PSI — moderate compressor requirement, same air draw as the 21-2266
• Pattern size: 14" — wider than the 21-2266's 10" and better suited for panels, doors, and flat work
• Why choose this setup: When you want the 1.5mm fluid volume of the 21-2266 family but need a wider fan to cover panels and flat surfaces more efficiently without stepping up to the 15 CFM of the 21-2466
• Key included components: 31-0615 fluid nozzle, 40-1115 needle, 21-2366 air cap, 60-1500 fan control assembly

Technical Specifications

Best for This Setup

The L100C-15-2366 is the wide-pattern counterpart to the L100C-15-2266 — same 1.5mm orifice and 12 CFM air draw, but the 21-2366 opens the fan to a 14" pattern that covers panels, doors, and flat work considerably faster than the 10" 21-2266 allows. This setup is the practical choice for woodworking and cabinet shops spraying medium-body urethanes and sealers over large flat panels, or for industrial operations finishing metal panels with medium-viscosity enamels where pattern width directly affects cycle time. The 12 CFM air draw keeps the compressor demand identical to the 21-2266 while delivering 40% more pattern width per pass — a meaningful efficiency gain on flat surfaces without any increase in air consumption. If you find yourself overlapping excessively with the L100C-15-2266 to build coverage on large panels, the L100C-15-2366 solves that directly without requiring you to step up to the 15 CFM of the 21-2466 series.

Frequently Asked Questions

What is the L100C-15-2366 best for?

Medium body enamels, urethanes, epoxy primers, and sealers on large flat surfaces including panels, doors, and millwork where a 14" pattern delivers better coverage efficiency than a 10" fan. The 1.5mm orifice handles medium-viscosity materials freely from a siphon cup at 12 CFM.

Is the L100C-15-2366 siphon or pressure feed?

Siphon feed. The 21-2366 is a siphon air cap, drawing material up from a siphon cup or siphon tank. For pressure feed applications at similar fluid volume, see the 21-2263 and 21-2266-3 pressure setups.

What air cap does the L100C-15-2366 use?

The 21-2366 siphon air cap — 12 CFM at 50 PSI, 14" maximum fan pattern. Compatible with 0.6mm through 1.8mm fluid tips.

What fluid nozzle and needle does this setup use?

The 31-0615 fluid nozzle (1.5mm / .059") paired with the 40-1115 needle (marked 115). The same 115 needle is used across all 1.5mm and 1.8mm Lynx 100C setups.

What repair kit fits the Lynx 100C?

Repair kit 10-106 covers all Lynx 100C configurations. It includes all wear seals, o-rings, springs, and needle seal components needed for a full gun rebuild.

Where can I find the full parts list and assembly diagram?

The complete Lynx 100C parts manual — including the full exploded parts diagram, air cap selection chart, and nozzle selection guide — is available for download from the CET manual page linked below.

Find the Right Lynx 100C Setup

Not sure which variant is right for your application? Use this table to match your coating material and feed preference to the correct setup. All model numbers link to their individual product pages.

CFM and pattern width at 50 PSI max inlet. Contact CET if you don't see your required configuration above.

Why the Lynx 100C?

The Lynx 100C is C.A. Technologies' answer to conventional spray gun dependability — a workhorse gun built for operators who need reliable, consistent performance across a wide variety of coating applications. The forged aluminum body keeps it lightweight and durable, while the all stainless steel fluid passages ensure compatibility with everything from thin inks and dyes to heavy body primers and adhesives.

• Forged aluminum body — lightweight, durable, and built for production use
• Stainless steel fluid passages — compatible with the full range of coatings from thin to thick
• Broad air cap selection — 21 air cap options across siphon, pressure, and internal mix configurations
• Available with carbide tipped fluid nozzles — for abrasive material applications
• Internal mix capability — for materials requiring internal atomization
• Flexible outfit options — 1 QT cups, 2 quart outfits, and tank outfits from 2.5 to 15 gallons
• US Made — designed and manufactured by C.A. Technologies

Available Outfits & Configurations

Parts Manual & Air Cap Selection Guide

The complete Lynx 100C parts manual includes the full exploded parts diagram, all air cap and nozzle selection charts, replacement part numbers, and assembly instructions.

Need Help?

Not sure which air cap or fluid nozzle combination is right for your coating material? Contact CET with your material type, viscosity, and feed preference. We'll help you select the correct Lynx 100C setup before you order.