null

Panther 100G PTFE Coated Glue Gun

(Showing 18 of 18)

 

 
 

C.A. Technologies · Authorized Distributor

Panther P100G
PTFE Adhesive Spray Gun

Pressure · Siphon · Waterborne Anti-Shear · US Made

PTFE Hard Coat 19 Configurations US Made

Not sure which P100G setup is right for your adhesive?  CET's team has been matching applications to configurations for over 20 years.

586-210-0555 ✉ sales@cetinc.com
19
Configurations
2.8mm
Max Orifice
3
Feed Types
PTFE
Hard Coat Body
50 PSI
Max Inlet

Overview

The Only Conventional Gun
Built for Adhesives.

The C.A. Technologies Panther 100G (P100G) is a PTFE hard coat conventional spray gun engineered specifically for adhesive and industrial coating applications where standard aluminum gun bodies foul, clog, and fail prematurely.

The PTFE hard coat on both the gun body and air cap prevents adhesive from bonding to contact surfaces — dramatically reducing cleanup time between runs. All stainless steel fluid passages provide full chemical resistance to solvent-based adhesives, contact cements, waterborne formulations, and aggressive industrial coatings.

Available in 19 CET Verified configurations spanning pressure feed, siphon feed, and the only waterborne adhesive anti-shear setup in the lineup — from 1.0mm thin sealers to 2.8mm ultra-heavy contact cements. US made in Louisville, CO.

At a Glance

Key Specifications

Feed Types PRESSURESIPHONWATERBORNE
Orifice Range 1.0mm – 2.8mm
Air Consumption 12 – 16.2 SCFM
Body Forged Aluminum, PTFE Hard Coat
Fluid Passages All Stainless Steel
Air Inlet 1/4” NPS (m)
Fluid Inlet 3/8” NPS (m)
Max Inlet Pressure 50 PSI
Fan Control 60-1500 (included)
Repair Kit 10-110 (fits all P100G)
Origin US Made — Louisville, CO

Why the P100G

Built Different From the Ground Up

PTFE Hard Coat Body & Air Cap

Prevents adhesive from bonding to both contact surfaces. Wipe clean instead of soak and scrub. The single biggest quality-of-life difference vs. a standard gun in adhesive work.

All Stainless Steel Fluid Passages

Full chemical resistance to solvent-based contact cements, waterborne adhesives, and aggressive industrial coatings. No corrosion or fluid passage degradation in extended production use.

Heavy Duty Needle Spring

Consistent trigger response and reliable needle return under the higher fluid resistance of thick contact cements and heavy adhesives. Built for production, not occasional use.

Waterborne Anti-Shear Config

The only P100G setup (P100G-18-1590) designed for waterborne adhesives — anti-shear internal mix atomizes water-based contact cements without degrading bond strength.

Carbide Nozzle Options

1.8mm, 2.2mm, and 2.8mm carbide nozzles available for abrasive or particle-laden adhesive formulations that would prematurely wear a stainless nozzle.

19 Verified Configurations

Pressure, siphon, and waterborne setups from 1.0mm to 2.8mm. One platform covers the full adhesive and industrial coating application range. CET verified every setup.

Material Selection

Viscosity & Feed Type Guide

Match your adhesive or coating to the correct orifice range, then use the configuration table below. Not sure? Call or text 586-210-0555 — CET will confirm the right setup before you order.

ViscosityZahn #2Typical MaterialsOrificeCompressor Min.
Thin 16–20 sec. Thin contact cements, lacquers, enamels, sealers 1.0 – 1.3mm 30-gal @ 90 PSI
Medium 20–28 sec. Medium adhesives, epoxy primers, urethane adhesives 1.3 – 1.8mm 60-gal @ 125 PSI
Heavy 28–35 sec. Heavy contact cements, high solid coatings, adhesives 1.8 – 2.2mm 60-gal @ 125 PSI
Ultra-Heavy >35 sec. Ultra-heavy contact cements, high viscosity industrial coatings 2.2 – 2.8mm 80-gal @ 125 PSI
Waterborne Adhesive Varies Waterborne contact cements, water-based adhesives 1.8mm 1590 only Confirm with CET

Pressure vs Siphon: Pressure feed pushes material to the gun under regulated air pressure — more consistent flow on heavier materials and at higher production volumes. Siphon feed draws material from a cup using venturi effect — simpler, portable, suited for batch work and lighter materials. For continuous production adhesive runs, CET recommends pressure feed.

All 19 Configurations

Complete Configuration Guide

All 19 configurations are CET Verified. Click any model number to view its full product page with specs, setup guidance, and pricing.

ModelNozzleAir CapFeedSCFMFanBest For
1.0mm
P100G-10-2266-3T 1.0mm 21-2266-3T PRESSURE 16.2 15" Thin adhesives, sealers
1.2mm
P100G-12-2266T 1.2mm 21-2266T SIPHON 12 10" Medium coatings, lacquers, portable
P100G-12-2266-3T 1.2mm 21-2266-3T PRESSURE 16.2 15" Thin-medium adhesives, lacquers
P100G-12-2263 1.2mm 21-2263 PRESSURE 14 14" Medium adhesives, primers
1.3mm
P100G-13-2266-3T 1.3mm 21-2266-3T PRESSURE 16.2 15" Medium adhesives, epoxy primers
P100G-13-2263 1.3mm 21-2263 PRESSURE 14 14" Medium adhesives, coatings
1.5mm
P100G-15-2266-3T 1.5mm 21-2266-3T PRESSURE 16.2 15" Adhesives, medium-heavy coatings
P100G-15-2263 1.5mm 21-2263 PRESSURE 14 14" Adhesives, medium-heavy
P100G-15-2266T 1.5mm 21-2266T SIPHON 12 10" Medium-heavy coatings, light adhesives
1.8mm
P100G-18-2266-3T 1.8mm 21-2266-3T PRESSURE 16.2 15" Adhesives, heavy coatings, PTFE cap
P100G-18-2266-3 1.8mm 21-2266-3 PRESSURE 16.2 15" Epoxies, high solid coatings
P100G-18-2263 1.8mm 21-2263 PRESSURE 14 14" Adhesives, heavy body — C.A. Tech recommended
P100G-18-2466 1.8mm 21-2466 SIPHON 15 14" Heavy coatings, primers, batch work
P100G-18-1590 1.8mm 1590 Anti-Shear WATERBORNE — — Waterborne adhesives only — call before ordering
2.2mm
P100G-22-2167 2.2mm 21-2167 PRESSURE 14.5 13" Heavy adhesives, high solid coatings
P100G-22-2267 2.2mm 21-2267 PRESSURE 15 13" Heavy adhesives, high solid coatings
P100G-22-2467 2.2mm 21-2467 SIPHON 15 13" Heavy coatings, high viscosity
2.8mm
P100G-28-2168 2.8mm 21-2168 PRESSURE 14 12" Ultra-heavy adhesives & coatings
P100G-28-2268 2.8mm 21-2268 SIPHON 15 14" Ultra-heavy coatings, batch work

PRESSURErequires pressurized fluid supply    SIPHONworks with standard siphon cup    WATERBORNEanti-shear internal mix — call before ordering

How Part Numbers Work

Reading a P100G Model Number

Every model follows: P100G – NOZZLE SIZE – AIR CAP

ExampleNozzleAir Cap
P100G-18-2263 1.8mm 21-2263 (pressure)
P100G-22-2467 2.2mm 21-2467 (siphon)
P100G-18-1590 1.8mm 1590 anti-shear (waterborne only)

Air caps ending in T (e.g. 2266T, 2266-3T) = PTFE coated  ·  Ending in -3 = 3-hole high-output  ·  Siphon caps carry 2X66T or 2X6X siphon series numbers. Unsure? Call 586-210-0555.

Complete Systems

Available Outfits

Part NumberTypeDescription
OP100G-130 2 Qt Economy Includes 5’ hose assemblies
OP100G-600 2 Qt Bandit Includes 5’ hose assemblies
Tank Outfits 2.5 – 15 Gallon 25’ hose — recommended for continuous production adhesive runs

Common Questions

Frequently Asked Questions

What makes the P100G different from a standard gun?

PTFE hard coat on both the gun body and air cap prevents adhesive from bonding to contact surfaces — wipe clean instead of soak and scrub. All stainless steel fluid passages resist solvent-based adhesives and waterborne formulations. Standard aluminum bodies foul quickly in adhesive environments.

Pressure vs. siphon feed for adhesive work?

Pressure feed pushes material under regulated air pressure — more consistent flow on heavier materials and at higher production volumes. Siphon feed draws material from a cup — simpler, portable, suited for batch work. For continuous production adhesive runs, CET recommends pressure feed.

What is the P100G-18-1590 and when do I need it?

The only P100G setup for waterborne adhesives. Uses a 1590 anti-shear internal mix outfit that atomizes water-based contact cements without the mechanical shear force that degrades waterborne adhesive chemistry and reduces bond strength. Call before ordering to confirm compatibility with your specific product.

What compressor do I need?

Siphon at 12 SCFM: 30-gallon @ 90 PSI. Pressure at 14 SCFM: 60-gallon minimum @ 125 PSI. High-output pressure at 16.2 SCFM: 80-gallon minimum @ 125 PSI. Call 586-210-0555 if unsure whether your existing compressor is sized correctly.

Are carbide nozzles available?

Yes — available as drop-in replacements at 1.8mm (31-0618V), 2.2mm, and 2.8mm (31-0628V) for abrasive or particle-laden formulations that cause premature stainless nozzle wear.

What repair kit does the P100G use?

All P100G configurations use repair kit 10-110 — all wear seals, o-rings, springs, and needle seal for a complete rebuild. CET stocks repair kits for same-day shipment.

Why Buy From CET

The CET Difference

20+ Years of Experience

CET has been matching customers to the right C.A. Technologies configuration since the beginning. We know these guns and adhesive applications inside and out.

Real Technical Support

Call or text 586-210-0555 to reach CET's technical team directly. We'll confirm your nozzle, air cap, and setup before you order — right the first time.

Verified Parts In Stock

CET stocks the gun, repair kit, air caps, and spare parts. You're never waiting on back-ordered components. Documentation included with every order.

Panther 100G Product Manual

Full parts diagram, air cap chart, nozzle selection guide & replacement part numbers for all P100G configurations.

⬇ Download Manual

Contact CET with your material type, viscosity, and feed preference — we'll confirm the correct Panther 100G configuration before you order.  586-210-0555  ·  sales@cetinc.com

Show 12