Description
C.A. Technologies Panther 100G — P100G-28-2268 (2.8mm Nozzle, 2268 Air Cap)
The C.A. Technologies Panther 100G P100G-28-2268 is a 2.8mm PTFE coated conventional siphon feed spray gun paired with the 21-2268 air cap — the maximum orifice siphon configuration in the P100G lineup, purpose-built for the thickest adhesives and ultra-heavy body industrial coatings that smaller orifices simply can’t pass without restricting. At 15 SCFM from a standard siphon cup, this setup handles ultra-heavy contact cements, thick urethane adhesives, and high viscosity coatings without requiring a pressure supply — making it the right choice for batch adhesive work and operations that need the P100G’s 2.8mm capacity but don’t run continuous production volumes that demand pressure feed consistency. Used in furniture manufacturing, industrial laminating, and heavy coating operations where the material is too thick for anything smaller than 2.8mm but a siphon setup is practical. All stainless steel fluid passages, PTFE hard coat gun body, US made. Call or text 586-210-0555 for setup guidance and availability before you order.
✓ 2.8mm stainless orifice — maximum orifice in the P100G lineup • ✓ PTFE coated gun body • ✓ Siphon feed — no pressure supply needed • ✓ 15 SCFM @ 50 PSI — requires 60-gallon compressor minimum • ✓ 14" max fan • ✓ US Made — CET Verified
Model: P100G-28-2268 • Nozzle: 2.8mm (.110") • Air Cap: 21-2268 • Feed: SIPHON • SCFM: 15 @ 50 PSI
Fan Control: 60-1500 (included) • Repair Kit: 10-110 • Max Inlet Pressure: 50 PSI • CET Verified Configuration
Overview
At a Glance
Specifications
Tech Specs
| Model | P100G-28-2268 |
| Fluid Nozzle | 31-0628 — 2.8mm (.110") 17-4PH Stainless |
| Air Cap | 21-2268 — Siphon, 15 SCFM |
| Needle | 40-1128 (128) — shared with P100G-28-2168 |
| Feed Type | SIPHON — standard siphon cup, no pressure pot or pump required |
| Max Inlet Pressure | 50 PSI |
| Air Consumption | 15 SCFM @ 50 PSI — requires minimum 60-gallon compressor at 125 PSI rated output |
| Max Pattern Width | 14" — controlled fan for targeted heavy material application |
| Air Inlet | 1/4" NPS (m) — standard shop air fitting, most compressors connect directly |
| Fluid Inlet | 3/8" NPS (m) — connects to standard siphon cup assembly |
| Body | Forged Aluminum — PTFE Hard Coat — prevents heavy adhesive and coating buildup on gun body surfaces |
| Fluid Passages | All Stainless Steel — full chemical resistance to solvent-based adhesives and ultra-heavy industrial coatings |
| Fan Control | 60-1500 (included) — adjusts from full 14" fan down for targeted application on narrower substrates |
| Repair Kit | 10-110 — complete rebuild kit, all seals, o-rings, springs and needle seal |
| Fulfillment | Most in-stock orders ship same day — stocked at C.A. Technologies’ Colorado facility. Call or text 586-210-0555 to confirm availability. |
| Origin | US Made — C.A. Technologies (Louisville, CO) |
Application
CET Application Match — Best for This Setup
The CET Preferred Setup for maximum orifice siphon work — when the material is too thick for 2.2mm but a full pressure feed system isn’t required or practical. Based on over 20 years supplying industrial finishing equipment, CET’s technical team recommends the P100G-28-2268 for furniture manufacturing, industrial laminating operations, and heavy coating applications running ultra-heavy contact cements and high viscosity coatings in batch quantities where the portability of siphon feed is an advantage over a fixed pressure supply setup.
Common Questions
Frequently Asked Questions
- What is the difference between the P100G-28-2268 and P100G-28-2168?
- Both use the 2.8mm fluid nozzle (31-0628) and the same 40-1128 needle. The 21-2268 is a siphon cap at 15 SCFM and 14" fan — no pressure supply needed, suited for batch work and portable applications. The 21-2168 is a pressure cap at 14 SCFM and 12" fan — requires pressurized fluid supply, delivers the most consistent flow for continuous production runs. For sustained high-volume adhesive production at 2.8mm, CET recommends the pressure configuration.
- What compressor do I need for 15 SCFM at 2.8mm?
- 15 SCFM at 50 PSI operating pressure with ultra-heavy materials requires a minimum 60-gallon compressor rated at 125 PSI output. With very thick materials that create more fluid resistance in the siphon cup, sustained spraying will tax compressor output more than lighter materials at the same SCFM. CET can advise on compressor sizing for your specific material — call or text 586-210-0555.
- Is a carbide nozzle available at 2.8mm?
- Yes — the 31-0628V carbide nozzle is a drop-in replacement for the 31-0628 stainless nozzle and significantly extends service life when spraying abrasive or particle-laden ultra-heavy coatings. Call or text 586-210-0555 to confirm if carbide is warranted for your application.
- What repair kit does the Panther 100G use?
- All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.
- What needle does the 2.8mm nozzle use?
- The 2.8mm fluid nozzle (31-0628) uses the 40-1128 (128) needle assembly — dedicated to the 2.8mm orifice size and shared only with the P100G-28-2168 pressure configuration. CET stocks replacement needles for same-day shipment.
- Where can I find the full Panther 100G parts manual?
- The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.
All Configurations
Find the Right Panther 100G for Your Application
The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Contact CET for a CET Application Match recommendation.
| Model | Nozzle | Air Cap | Feed | SCFM | Best For | Order |
|---|---|---|---|---|---|---|
| P100G-10-2266-3T | 1.0mm | 21-2266-3T | PRESSURE | 16.2 | Thin adhesives, sealers | Order |
| P100G-12-2266T | 1.2mm | 21-2266T | SIPHON | 12 | Medium coatings, lacquers | Order |
| P100G-12-2266-3T | 1.2mm | 21-2266-3T | PRESSURE | 16.2 | Thin-medium adhesives, lacquers | Order |
| P100G-12-2263 | 1.2mm | 21-2263 | PRESSURE | 14 | Medium adhesives, primers | Order |
| P100G-13-2266-3T | 1.3mm | 21-2266-3T | PRESSURE | 16.2 | Medium adhesives, epoxy primers | Order |
| P100G-13-2263 | 1.3mm | 21-2263 | PRESSURE | 14 | Medium adhesives, coatings | Order |
| P100G-15-2266-3T | 1.5mm | 21-2266-3T | PRESSURE | 16.2 | Adhesives, medium-heavy coatings | Order |
| P100G-15-2263 | 1.5mm | 21-2263 | PRESSURE | 14 | Adhesives, medium-heavy | Order |
| P100G-15-2266T | 1.5mm | 21-2266T | SIPHON | 12 | Medium-heavy coatings, light adhesives | Order |
| P100G-18-2266-3T | 1.8mm | 21-2266-3T | PRESSURE | 16.2 | Adhesives, heavy coatings | Order |
| P100G-18-2266-3 | 1.8mm | 21-2266-3 | PRESSURE | 16.2 | Epoxies, high solid coatings | Order |
| P100G-18-2263 | 1.8mm | 21-2263 | PRESSURE | 14 | Adhesives, heavy body | Order |
| P100G-18-2466 | 1.8mm | 21-2466 | SIPHON | 15 | Heavy coatings, primers | Order |
| P100G-18-1590 | 1.8mm | 1590 | WATERBORNE | — | Waterborne adhesives — anti-shear | Order |
| P100G-22-2167 | 2.2mm | 21-2167 | PRESSURE | 14.5 | Heavy adhesives, high solid coatings | Order |
| P100G-22-2267 | 2.2mm | 21-2267 | PRESSURE | 15 | Heavy adhesives, high solid coatings | Order |
| P100G-22-2467 | 2.2mm | 21-2467 | SIPHON | 15 | Heavy coatings, high viscosity | Order |
| P100G-28-2168 | 2.8mm | 21-2168 | PRESSURE | 14 | Ultra-heavy adhesives & coatings | Order |
| P100G-28-2268 | 2.8mm | 21-2268 | SIPHON | 15 | Ultra-heavy coatings | Current |
PRESSURE requires pressurized fluid supply SIPHON works with standard siphon cup WATERBORNE anti-shear internal mix, waterborne adhesives only
Why Buy From CET
The CET Difference
- Over 20 years supplying industrial finishing equipment — CET has been matching customers to the right C.A. Technologies configuration since the beginning. We know these guns inside and out.
- Real technical support before and after the sale — call or text 586-210-0555 to reach CET’s technical team directly. We’ll confirm your nozzle, air cap, and setup before you order so you get it right the first time.
- Fast fulfillment on most in-stock orders — C.A. Technologies stocks these guns at their Colorado facility and most orders ship same day. Call or text 586-210-0555 to verify availability and confirm your ship date before ordering.
- Verified part compatibility — every configuration on this page is CET Verified. We stock the gun, the repair kit, the air caps, and the spare parts — so you’re never waiting on back-ordered components.
- Documentation included — every order ships with access to the full parts manual, air cap chart, and nozzle selection guide. No hunting for documentation after the sale.
- The best order fulfillment in the industry — you receive updates at every step of the process so you know exactly where your order is at all times. And in the rare case there’s a delay, we’ll let you know in advance — so you’re never chasing an order down again.
Why Choose the Panther 100G
Built for Adhesives That Standard Guns Can’t Handle
The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap — the critical advantage when spraying adhesives and aggressive coatings that foul standard aluminum gun bodies and air cap faces during production.
- PTFE hard coat body: Prevents heavy adhesive and coating buildup on the gun body — faster cleanup after ultra-heavy material runs.
- All stainless steel fluid passages: Full chemical resistance to heavy solvent-based adhesives and industrial coatings for long production life.
- Heavy duty needle spring: Consistent trigger response and reliable needle return even under the higher fluid resistance of ultra-heavy materials.
- Forged aluminum body: Lightweight for reduced operator fatigue — durable enough for demanding industrial environments.
- 19 configurations: From 1.0mm thin adhesive sealers to 2.8mm ultra-heavy pressure and siphon setups, and the only waterborne anti-shear configuration in the lineup.
Outfits & Configurations
Available Outfits
| Part Number | Type | Description |
|---|---|---|
| OP100G-130 | 2 Quart Outfit (Economy) | Includes 5' hose assemblies |
| OP100G-600 | 2 Quart Outfit (Bandit) | Includes 5' hose assemblies |
| Tank Outfits | 2.5, 5, 10, 12.5, 15 Gallon | Includes 25' hose assemblies — suitable for continuous production runs |
Panther 100G Product Manual
Full parts diagram, air cap chart, nozzle selection guide & replacement part numbers for all P100G configurations
Download the Panther 100G ManualNeed Help Selecting the Right Configuration?
Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.
