Description
Spray Waterborne Adhesives Without Destroying Bond Strength — C.A. Technologies Panther 100G P100G-18-1590
Most conventional spray guns shear waterborne adhesives during atomization — breaking down the polymer chains that create bond strength before the material ever hits the substrate. The C.A. Technologies Panther 100G P100G-18-1590 solves this with a dedicated 1590 anti-shear internal mix outfit that atomizes water-based contact cements and waterborne adhesives without disrupting their chemistry, so you get consistent bond performance on every panel, every run. The 1.8mm stainless fluid nozzle is sized for the flow characteristics of waterborne formulations, and the PTFE hard coat gun body resists water-based adhesive buildup so cleanup stays fast even after long production runs. If your operation has moved to waterborne adhesives for VOC compliance or customer specification and you’re struggling with bond inconsistency, poor coverage, or excessive gun fouling — this is the setup C.A. Technologies built for that problem. Call or text 586-210-0555 before ordering so CET’s technical team can confirm compatibility with your specific waterborne formulation.
✓ Anti-shear internal mix — preserves waterborne adhesive chemistry • ✓ 1.8mm stainless orifice • ✓ PTFE coated gun body — resists water-based buildup • ✓ All stainless fluid passages — corrosion resistant to waterborne formulations • ✓ US Made — CET Verified
Model: P100G-18-1590 • Nozzle: 1.8mm (.071") • Outfit: 1590 Anti-Shear • Feed: WATERBORNE • Application: Waterborne contact cements & water-based adhesives
Repair Kit: 10-110 • CET Verified Configuration • Call or text 586-210-0555 — always confirm before ordering
Overview
At a Glance
Specifications
Tech Specs
| Model | P100G-18-1590 |
| Fluid Nozzle | 31-0618 — 1.8mm (.071") 17-4PH Stainless |
| Outfit / Air Cap | 1590 Anti-Shear — Internal Mix, Waterborne Configuration |
| Needle | 40-1115 (115) — shared with 1.5mm and 1.8mm configurations |
| Feed Type | WATERBORNE — waterborne adhesives only |
| Atomization Type | Internal mix — air and fluid meet inside the cap, not externally, reducing the mechanical shear force that degrades waterborne chemistry |
| Air Inlet | 1/4" NPS (m) — standard 1/4" shop air fitting, most compressors connect directly |
| Fluid Inlet | 3/8" NPS (m) — connects to standard pressure pot or siphon hose assemblies |
| Body | Forged Aluminum — PTFE Hard Coat — resists water-based adhesive curing on gun body surfaces |
| Fluid Passages | All Stainless Steel — fully corrosion resistant to waterborne formulations for long production life |
| Repair Kit | 10-110 — complete rebuild kit, all seals, o-rings, springs and needle seal |
| Fulfillment | Most in-stock orders ship same day — stocked at C.A. Technologies’ Colorado facility. Call or text 586-210-0555 to confirm availability and formulation compatibility before ordering. |
| Origin | US Made — C.A. Technologies (Louisville, CO) |
Application
CET Application Match — Built for the Waterborne Transition
The CET Preferred Setup for operations that have moved to waterborne adhesive formulations and need a gun that works with water-based chemistry rather than against it. Based on over 20 years supplying industrial finishing equipment, CET’s technical team sees the same failure pattern repeatedly when shops switch to waterborne adhesives using standard guns: inconsistent bonds, poor open time, and fouled equipment — all caused by shear damage during atomization. The P100G-18-1590 eliminates that problem at the source.
Common Questions
Frequently Asked Questions
- Why can’t I just use a standard Panther 100G configuration for waterborne adhesives?
- Standard external mix air caps atomize by directing high-velocity air at the fluid stream as it exits the nozzle — a process that generates enough mechanical shear to damage the polymer structure of waterborne adhesives. This shows up as inconsistent bonding, reduced open time, and adhesive that doesn’t perform to its spec sheet. The 1590 internal mix outfit is designed to prevent this. Using the wrong gun for waterborne adhesives doesn’t just reduce performance — it can make the product look defective when the real issue is the application equipment.
- Can I use the P100G-18-1590 for solvent-based adhesives?
- No — the 1590 outfit is designed specifically for waterborne formulations. For solvent-based contact cements and adhesives at 1.8mm, CET recommends the P100G-18-2263 (C.A. Tech pressure recommendation for adhesives), P100G-18-2266-3T (high-flow pressure with PTFE cap), or P100G-18-2466 (siphon). Call or text 586-210-0555 to confirm the right setup.
- How do I know if my adhesive is truly “waterborne” and needs this setup?
- Waterborne adhesives use water as the primary carrier solvent rather than petroleum-based solvents. They typically have low VOC content, require water for cleanup, and the SDS will list water as a primary component. If your adhesive manufacturer specifies anti-shear or low-shear spray equipment, this is the setup. If you’re unsure, call CET at 586-210-0555 with your product name — we’ll confirm the right configuration.
- What compressor do I need for this setup?
- Compressor requirements for the 1590 waterborne setup depend on the specific air consumption of your configuration and should be confirmed with CET’s technical team for your application. As a general rule, conventional spray setups at this orifice size typically require a minimum 60-gallon compressor with an output of at least 125 PSI. Call or text 586-210-0555 and we’ll confirm the right compressor spec for your specific waterborne setup and production volume.
- What repair kit does the Panther 100G use?
- All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. CET stocks repair kits for same-day shipment — call or text 586-210-0555 to confirm availability.
- Where can I find the full Panther 100G parts manual?
- The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.
All Configurations
Find the Right Panther 100G for Your Application
The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Contact CET for a CET Application Match recommendation.
| Model | Nozzle | Air Cap | Feed | SCFM | Best For | Order |
|---|---|---|---|---|---|---|
| P100G-10-2266-3T | 1.0mm | 21-2266-3T | PRESSURE | 16.2 | Thin adhesives, sealers | Order |
| P100G-12-2266T | 1.2mm | 21-2266T | SIPHON | 12 | Medium coatings, lacquers | Order |
| P100G-12-2266-3T | 1.2mm | 21-2266-3T | PRESSURE | 16.2 | Thin-medium adhesives, lacquers | Order |
| P100G-12-2263 | 1.2mm | 21-2263 | PRESSURE | 14 | Medium adhesives, primers | Order |
| P100G-13-2266-3T | 1.3mm | 21-2266-3T | PRESSURE | 16.2 | Medium adhesives, epoxy primers | Order |
| P100G-13-2263 | 1.3mm | 21-2263 | PRESSURE | 14 | Medium adhesives, coatings | Order |
| P100G-15-2266-3T | 1.5mm | 21-2266-3T | PRESSURE | 16.2 | Adhesives, medium-heavy coatings | Order |
| P100G-15-2263 | 1.5mm | 21-2263 | PRESSURE | 14 | Adhesives, medium-heavy | Order |
| P100G-15-2266T | 1.5mm | 21-2266T | SIPHON | 12 | Medium-heavy coatings, light adhesives | Order |
| P100G-18-2266-3T | 1.8mm | 21-2266-3T | PRESSURE | 16.2 | Adhesives, heavy coatings | Order |
| P100G-18-2266-3 | 1.8mm | 21-2266-3 | PRESSURE | 16.2 | Epoxies, high solid coatings | Order |
| P100G-18-2263 | 1.8mm | 21-2263 | PRESSURE | 14 | Adhesives, heavy body | Order |
| P100G-18-2466 | 1.8mm | 21-2466 | SIPHON | 15 | Heavy coatings, primers | Order |
| P100G-18-1590 | 1.8mm | 1590 | WATERBORNE | — | Waterborne adhesives — anti-shear | Current |
| P100G-22-2167 | 2.2mm | 21-2167 | PRESSURE | 14.5 | Heavy adhesives, high solid coatings | Order |
| P100G-22-2267 | 2.2mm | 21-2267 | PRESSURE | 15 | Heavy adhesives, high solid coatings | Order |
| P100G-22-2467 | 2.2mm | 21-2467 | SIPHON | 15 | Heavy coatings, high viscosity | Order |
| P100G-28-2168 | 2.8mm | 21-2168 | PRESSURE | 14 | Ultra-heavy adhesives & coatings | Order |
| P100G-28-2268 | 2.8mm | 21-2268 | SIPHON | 15 | Ultra-heavy coatings | Order |
PRESSURE requires pressurized fluid supply SIPHON works with standard siphon cup WATERBORNE anti-shear internal mix — waterborne adhesives only
Why Buy From CET
The CET Difference
- Over 20 years supplying industrial finishing equipment — CET has been matching customers to the right C.A. Technologies configuration since the beginning. We know these guns inside and out.
- Real technical support before and after the sale — call or text 586-210-0555 to reach CET’s technical team directly. For waterborne setups especially, we recommend a quick call before ordering to confirm your specific formulation is compatible.
- Fast fulfillment on most in-stock orders — C.A. Technologies stocks these guns at their Colorado facility and most orders ship same day. Call or text 586-210-0555 to verify availability and confirm your ship date before ordering.
- Verified part compatibility — every configuration on this page is CET Verified. We stock the gun, the repair kit, the air caps, and the spare parts — so you’re never waiting on back-ordered components.
- Documentation included — every order ships with access to the full parts manual, air cap chart, and nozzle selection guide. No hunting for documentation after the sale.
- The best order fulfillment in the industry — you receive updates at every step of the process so you know exactly where your order is at all times. And in the rare case there’s a delay, we’ll let you know in advance — so you’re never chasing an order down again.
Why Choose the Panther 100G
Built for Adhesives That Standard Guns Can’t Handle
The Panther 100G is the only gun in the C.A. Technologies conventional lineup with PTFE hard coat on the gun body — and the only one configurable for waterborne adhesive chemistry. For operations running aggressive adhesive formulations where standard guns foul quickly, bond inconsistently, or degrade the material during application, the Panther 100G platform is the answer.
- PTFE hard coat body: Prevents adhesive — waterborne or solvent-based — from bonding to the gun body, dramatically cutting cleanup time after production runs.
- All stainless steel fluid passages: Full corrosion and chemical resistance across both waterborne and solvent-based adhesive formulations.
- Heavy duty needle spring: Consistent trigger response and reliable needle return under continuous all-day production use.
- Forged aluminum body: Lightweight for reduced fatigue on long production shifts — durable enough for demanding industrial environments.
- 19 configurations: From 1.0mm thin adhesive sealers to 2.8mm ultra-heavy pressure setups, and the only waterborne anti-shear configuration in the lineup — one gun platform covers the full adhesive and coating application range.
Outfits & Configurations
Available Outfits
| Part Number | Type | Description |
|---|---|---|
| OP100G-130 | 2 Quart Outfit (Economy) | Includes 5' hose assemblies |
| OP100G-600 | 2 Quart Outfit (Bandit) | Includes 5' hose assemblies |
| Tank Outfits | 2.5, 5, 10, 12.5, 15 Gallon | Includes 25' hose assemblies — suitable for continuous production runs |
Panther 100G Product Manual
Full parts diagram, air cap chart, nozzle selection guide & replacement part numbers for all P100G configurations
Download the Panther 100G ManualNot Sure This Is the Right Setup for Your Waterborne Product?
Call before you order. CET’s technical team has been specifying waterborne adhesive spray setups for over 20 years — we’ll confirm whether the P100G-18-1590 is right for your specific formulation, viscosity, and production volume in a 5-minute call. Call or text 586-210-0555.
