C.A. Technologies Panther 100G — P100G-12-2266-3T (1.2mm Nozzle, 2266-3T Air Cap)

The C.A. Technologies Panther 100G P100G-12-2266-3T is a 1.2mm PTFE coated conventional pressure feed spray gun paired with the 21-2266-3T air cap — the high-flow, wide-fan PTFE pressure configuration for thin-to-medium adhesives and coatings. At 16.2 SCFM and a 15" maximum fan under pressure, this setup delivers strong atomization of 1.2mm materials with the PTFE coated air cap’s non-stick surface keeping cleanup fast after adhesive runs. Well suited for thin contact cements, adhesive sealers, lacquers, and medium body enamels where PTFE cleanup advantage matters alongside precision orifice control. Used in cabinet shops, woodworking operations, and industrial finishing lines running thin adhesive and finish coating applications daily. The PTFE hard coat on both the gun body and air cap resists material buildup. All stainless steel fluid passages. US made. Call or text 586-210-0555 for setup guidance and availability before you order.

Overview

At a Glance

• Configuration: 1.2mm stainless steel fluid nozzle + 21-2266-3T PTFE coated pressure air cap — CET Verified Configuration
• Best for: Thin-to-medium adhesives, contact cements, lacquers, enamels, and sealers in the 16–25 sec. Zahn #2 range
• Feed type: PRESSURE — consistent high-flow delivery with 15" fan and 16.2 SCFM
• Air consumption: 16.2 SCFM @ 50 PSI max inlet
• Body: PTFE hard coat anodized forged aluminum — resists adhesive and coating buildup for fast cleanup
• Fluid passages: All stainless steel for full chemical resistance
• Fast fulfillment — most in-stock orders ship same day. Call or text 586-210-0555 to verify availability before you order.
• Origin: US Made by C.A. Technologies (Louisville, CO) — distributed by CET for over 20 years

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The P100G-12-2266-3T is a CET Preferred Setup when you need the highest SCFM and widest fan at 1.2mm — combined with the PTFE non-stick advantage of the 21-2266-3T cap for fast adhesive cleanup. Based on over 20 years supplying industrial finishing equipment, CET’s technical team specifies this configuration for cabinet shops and woodworking operations running thin contact cement formulations, lacquers, and medium body enamels where the wider 15" fan covers large substrate areas efficiently and the PTFE coating keeps cleanup time short between runs.

At 16.2 SCFM this is the highest air consumption pressure cap in the P100G lineup — it provides strong atomization energy through the 1.2mm orifice, producing a clean, wide fan pattern for thin-to-medium materials. For the same 1.2mm orifice at lower SCFM and without the PTFE coating, the P100G-12-2263 is the alternative.

• Cabinet and woodworking shops: Wide 15" fan covers panel goods and case goods surfaces efficiently with thin adhesives and lacquer finishes
• Thin contact cements and sealers: 1.2mm orifice controls flow precisely for thin formulations that over-apply through larger orifices
• Production finishing lines: PTFE coated air cap keeps spray pattern consistent and cleanup fast between material changes
• Lacquers and medium enamels: 16.2 SCFM delivers clean atomization of thin-to-medium finish coatings into a full 15" fan under pressure

Common Questions

Frequently Asked Questions

How does the P100G-12-2266-3T compare to the P100G-12-2263 and P100G-12-2266T?

All three use the same 1.2mm fluid nozzle (31-0612). The P100G-12-2266-3T uses the 21-2266-3T — pressure feed, 16.2 SCFM, 15" fan, PTFE coated cap. The P100G-12-2263 uses the 21-2263 — pressure feed, 14 SCFM, 14" fan, standard aluminum cap. The P100G-12-2266T uses the 21-2266T — siphon feed, 12 SCFM, 10" fan, PTFE coated cap. Choose the 2266-3T when you need the widest fan and highest flow under pressure with PTFE cleanup advantage. Choose the 2263 for a lower-SCFM pressure option. Choose the 2266T for siphon feed.

Why use 16.2 SCFM for a 1.2mm orifice — isn’t that a lot of air?

The higher SCFM of the 21-2266-3T provides strong atomization energy that produces a wider, more even fan pattern even through the small 1.2mm orifice. For thin materials that need to be broken up finely and spread across a wide area, the additional air volume is an advantage. The fan control knob lets you narrow the pattern if needed for targeted application.

What materials work best with a 1.2mm fluid nozzle?

The 1.2mm orifice handles thin-to-medium viscosity materials in the 16–25 second Zahn #2 range — thin contact cements, lacquers, enamels, primers, and sealers. For slightly thicker materials in the 25–30 sec. range, stepping up to 1.3mm or 1.5mm may give better flow. CET can help confirm — call or text 586-210-0555.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

What needle does the 1.2mm nozzle use?

The 1.2mm fluid nozzle (31-0612) uses the 40-1110 (110) needle assembly — shared with the 1.0mm and 1.3mm configurations. CET stocks replacement needles for same-day shipment.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Use the table below to find the right nozzle and air cap combination for your material, or contact CET for a CET Application Match recommendation.

PRESSURE requires pressurized fluid supply    SIPHON works with standard siphon cup    WATERBORNE anti-shear setup for waterborne adhesives

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

PTFE Coated Durability for Demanding Applications

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap. This matters most when spraying adhesives, contact cements, and other sticky or aggressive coatings that tend to foul standard aluminum gun bodies and air cap faces.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to surfaces, dramatically reducing cleaning time and extending component life.
• All stainless steel fluid passages: Full chemical resistance across solvent-based, waterborne, and aggressive adhesive formulations.
• Heavy duty needle spring: Maintains consistent trigger response and needle return under continuous production use.
• Forged aluminum body: Lightweight and durable — built for all-day production use without fatigue.
• 17 air cap options: From 0.6mm siphon to 2.8mm pressure — one platform covers the full range of coating viscosities.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.