C.A. Technologies Panther 100G — P100G-12-2266T (1.2mm Nozzle, 2266T Air Cap)

The C.A. Technologies Panther 100G P100G-12-2266T is a 1.2mm PTFE coated conventional siphon feed spray gun paired with the 21-2266T PTFE coated air cap — the only siphon configuration in the P100G lineup that combines the precision of a 1.2mm orifice with PTFE non-stick on the air cap for fast cleanup after adhesive and coating runs. At 12 SCFM from a standard siphon cup, this setup handles thin-to-medium contact cements, lacquers, enamels, and sealers without requiring a pressurized fluid supply — just a siphon cup and a shop air line. Used in cabinet shops, woodworking operations, and industrial finishing lines doing varied thin adhesive and finish coating work where portability and PTFE cleanup convenience matter more than maximum fan width or pressure feed consistency. All stainless steel fluid passages, PTFE hard coat gun body, US made. Call or text 586-210-0555 for setup guidance and availability before you order.

✓ 1.2mm stainless orifice  •  ✓ PTFE coated body & air cap  •  ✓ Siphon feed — no pressure supply needed  •  ✓ 12 SCFM @ 50 PSI — works with 30-gallon compressor minimum  •  ✓ 10" max fan  •  ✓ US Made — CET Verified

Overview

At a Glance

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The CET Preferred Setup for siphon-fed 1.2mm work where PTFE non-stick cleanup matters and no pressure supply is available or preferred. Based on over 20 years supplying industrial finishing equipment, CET’s technical team recommends the P100G-12-2266T for cabinet shops and woodworking operations running thin contact cements, lacquers, and medium body enamels that need to move the gun between workstations — siphon cup and air line is all the setup required, and the PTFE air cap keeps cleanup fast when switching between adhesive and finish coat runs.

Common Questions

Frequently Asked Questions

What is the difference between the P100G-12-2266T and P100G-12-2266-3T?

Both use the 1.2mm fluid nozzle (31-0612) with a PTFE coated air cap. The 21-2266T is a siphon cap at 12 SCFM and 10" fan — no pressure supply needed. The 21-2266-3T is a pressure cap at 16.2 SCFM and 15" fan — requires a pressurized fluid supply but delivers a wider fan and more air volume. Choose the 2266T for siphon convenience; choose the 2266-3T for production pressure runs.

What compressor do I need for 12 SCFM?

12 SCFM at 50 PSI operating pressure is achievable with a 30-gallon compressor rated at 90 PSI output — one of the lower compressor demands in the P100G lineup, making this a practical choice for smaller shops. If you’re unsure about your compressor’s capability, call or text 586-210-0555 and CET’s team can advise.

What materials work best with a 1.2mm fluid nozzle?

The 1.2mm orifice handles thin-to-medium viscosity materials in the 16–25 second Zahn #2 range — thin contact cements, lacquers, enamels, automotive base coats, and sealers. For thicker materials in the 25–30 sec. range, step up to 1.3mm or 1.5mm. CET can confirm the right orifice for your material — call or text 586-210-0555.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

What needle does the 1.2mm nozzle use?

The 1.2mm fluid nozzle (31-0612) uses the 40-1110 (110) needle assembly — shared with the 1.0mm and 1.3mm configurations, so one spare covers three orifice sizes. CET stocks replacement needles for same-day shipment.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Contact CET for a CET Application Match recommendation.

PRESSURE requires pressurized fluid supply    SIPHON works with standard siphon cup    WATERBORNE anti-shear internal mix, waterborne adhesives only

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

Built for Adhesives That Standard Guns Can’t Handle

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap — the critical advantage when spraying adhesives and coatings that foul standard aluminum gun bodies and air cap faces during production.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to both surfaces — wipe clean instead of soak and scrub, dramatically cutting cleanup time between runs.
• All stainless steel fluid passages: Full chemical resistance to solvent-based adhesives, lacquers, and industrial coatings for long production life.
• Heavy duty needle spring: Consistent trigger response and reliable needle return under continuous all-day production use.
• Forged aluminum body: Lightweight for reduced operator fatigue — durable enough for demanding industrial environments.
• 19 configurations: From 1.0mm thin adhesive sealers to 2.8mm ultra-heavy pressure setups and the only waterborne anti-shear configuration in the lineup.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.