C.A. Technologies Panther 100G — P100G-13-2263 (1.3mm Nozzle, 2263 Air Cap)

The C.A. Technologies Panther 100G P100G-13-2263 is a 1.3mm PTFE coated conventional pressure feed spray gun paired with the 21-2263 air cap — one of C.A. Technologies’ recommended configurations for adhesive spraying at medium viscosities. At 14 SCFM and pressure feed, this setup delivers consistent, controlled flow of contact cements, urethane adhesives, epoxy primers, and medium body industrial coatings in the 21–30 second Zahn #2 range. The 1.3mm orifice sits between the precision of 1.2mm and the heavier flow of 1.5mm — making it the right choice when material viscosity calls for slightly more fluid passage than a 1.2mm provides but the full flow of a 1.5mm is too much. Used in cabinet shops, woodworking operations, and industrial finishing lines where medium adhesives and finish coatings are applied under pressure daily. The PTFE hard coat on both the gun body and air cap resists material buildup and simplifies cleanup. All stainless steel fluid passages. US made. Call or text 586-210-0555 for setup guidance and availability before you order.

Overview

At a Glance

• Configuration: 1.3mm stainless steel fluid nozzle + 21-2263 pressure air cap — CET Verified Configuration
• Best for: Medium adhesives, contact cements, epoxy primers, and industrial coatings in the 21–30 sec. Zahn #2 range requiring precise pressure feed flow
• Feed type: PRESSURE — consistent flow control at medium orifice for production adhesive applications
• Air consumption: 14 SCFM @ 50 PSI max inlet
• Body: PTFE hard coat anodized forged aluminum — resists adhesive and coating buildup for fast cleanup
• Fluid passages: All stainless steel for full chemical resistance
• Fast fulfillment — most in-stock orders ship same day. Call or text 586-210-0555 to verify availability before you order.
• Origin: US Made by C.A. Technologies (Louisville, CO) — distributed by CET for over 20 years

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The P100G-13-2263 is a CET Preferred Setup for medium adhesive and coating applications where precise orifice sizing matters. Based on over 20 years supplying industrial finishing equipment, CET’s technical team recommends the 1.3mm configuration when customers need more flow than a 1.2mm delivers but find a 1.5mm over-applies their material. The 21-2263 pressure air cap at 14 SCFM provides consistent, controlled delivery — particularly well suited for contact cements, epoxy primers, and medium body industrial coatings applied in cabinet shops and woodworking operations daily.

At 1.3mm under pressure with a 14" maximum fan, this setup gives precise coverage and controlled deposit weight for medium viscosity adhesives and finishes. The 21-2263 is one of C.A. Technologies’ recommended air caps for adhesive applications at this orifice range — delivering the pressure feed consistency that matters when coverage uniformity across a production run is critical.

• Cabinet and woodworking shops: Medium contact cement and epoxy primer application where 1.3mm orifice precision gives better coverage control than larger orifices
• Epoxy primers and sealers: 1.3mm at 14 SCFM atomizes medium body epoxy formulations cleanly under pressure for uniform primer coats
• Medium body industrial coatings: Consistent pressure feed at 1.3mm delivers repeatable deposit weight across production finishing runs
• Precision adhesive work: Tighter orifice control reduces over-application on smaller substrates and detail components

Common Questions

Frequently Asked Questions

When should I choose 1.3mm over 1.2mm or 1.5mm?

The 1.3mm sits right between the precision of 1.2mm and the heavier flow of 1.5mm. Choose 1.3mm when your material is a true medium viscosity — thin enough that 1.5mm over-deposits but thick enough that 1.2mm restricts flow or leaves an uneven pattern. Contact cements, epoxy primers, and medium body enamels in the 21–28 second Zahn #2 range are typical candidates. Not sure? Call or text CET at 586-210-0555 and we’ll help dial in the right orifice.

What is the difference between the P100G-13-2263 and P100G-13-2266-3T?

Both use a 1.3mm fluid nozzle under pressure. The 21-2263 runs at 14 SCFM with a standard aluminum air cap and a 14" max fan. The 21-2266-3T runs at 16.2 SCFM with a PTFE coated air cap and a wider 15" fan. CET recommends the 2266-3T when PTFE non-stick cleanup is the priority for adhesive applications; the 2263 is an excellent all-round pressure configuration at 1.3mm for medium coatings and adhesives.

Is this setup suitable for epoxy coatings?

Yes — the 1.3mm orifice at 14 SCFM handles medium body epoxy primers and sealers well under pressure. The all stainless steel fluid passages and PTFE coated body provide full chemical resistance to epoxy formulations. CET’s technical team can confirm suitability for your specific epoxy system — call or text 586-210-0555.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

What needle does the 1.3mm nozzle use?

The 1.3mm fluid nozzle (31-0613) uses the 40-1110 (110) needle assembly — the same needle used for 1.0mm and 1.2mm configurations. CET stocks replacement needles for same-day shipment.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Use the table below to find the right nozzle and air cap combination for your material, or contact CET for a CET Application Match recommendation.

PRESSURE requires pressurized fluid supply    SIPHON works with standard siphon cup    WATERBORNE anti-shear setup for waterborne adhesives

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

PTFE Coated Durability for Demanding Applications

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap. This matters most when spraying adhesives, contact cements, and other sticky or aggressive coatings that tend to foul standard aluminum gun bodies and air cap faces.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to surfaces, dramatically reducing cleaning time and extending component life.
• All stainless steel fluid passages: Full chemical resistance across solvent-based, waterborne, and aggressive adhesive formulations.
• Heavy duty needle spring: Maintains consistent trigger response and needle return under continuous production use.
• Forged aluminum body: Lightweight and durable — built for all-day production use without fatigue.
• 17 air cap options: From 0.6mm siphon to 2.8mm pressure — one platform covers the full range of coating viscosities.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.