C.A. Technologies Panther 100G — P100G-15-2263 (1.5mm Nozzle, 2263 Air Cap)

The C.A. Technologies Panther 100G P100G-15-2263 is a 1.5mm PTFE coated conventional pressure feed spray gun paired with the 21-2263 air cap — one of C.A. Technologies’ recommended configurations for adhesive spraying at medium-to-heavy viscosities. At 14 SCFM and pressure feed, this setup delivers consistent, controlled flow of contact cements, urethane adhesives, high solid enamels, and industrial coatings in the 21–30 second Zahn #2 range. The PTFE hard coat on both the gun body and air cap resists material buildup and simplifies cleanup. All stainless steel fluid passages. US made. Call or text 586-210-0555 for setup guidance and availability before you order.

Overview

At a Glance

• Configuration: 1.5mm stainless steel fluid nozzle + 21-2263 pressure air cap — CET Verified Configuration
• Best for: Contact cements, urethane adhesives, high solid enamels, and medium-to-heavy coatings in the 21–30 sec. Zahn #2 range
• Feed type: PRESSURE — consistent flow for production adhesive and coating applications
• Air consumption: 14 SCFM @ 50 PSI max inlet
• Body: PTFE hard coat anodized forged aluminum — resists adhesive and coating buildup for fast cleanup
• Fluid passages: All stainless steel for full chemical resistance
• Fast fulfillment — most in-stock orders ship same day. Call or text 586-210-0555 to verify availability before you order.
• Origin: US Made by C.A. Technologies (Louisville, CO) — distributed by CET for over 20 years

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The P100G-15-2263 is a CET Preferred Setup for adhesive and finish coating applications where pressure feed consistency matters and material viscosity sits in the medium-to-heavy range. C.A. Technologies specifically recommends the 21-2263 air cap for adhesive spraying — at 14 SCFM under pressure, this configuration delivers steady, controlled flow of contact cements, urethane adhesives, and high solid coatings without the flow drop variability you get from siphon setups. Based on over 20 years supplying industrial finishing equipment, CET’s technical team regularly specifies this configuration for woodworking, furniture manufacturing, and industrial laminating operations running contact cements and urethane adhesives where a 1.5mm orifice matches the material viscosity better than a 1.8mm.

• Furniture and cabinet shops: Daily pressure-fed contact cement and urethane adhesive application on panel goods and case goods lines
• Industrial laminating: Consistent pressure feed flow at 1.5mm keeps adhesive coverage uniform across large substrate runs
• High solid enamels and urethanes: 1.5mm at 14 SCFM handles medium-to-heavy finish coatings cleanly under pressure
• Production finishing lines: Pressure feed with tank outfit eliminates re-cupping downtime for continuous spray operations

Common Questions

Frequently Asked Questions

What is the difference between the P100G-15-2263 and P100G-18-2263?

Both use the 21-2263 pressure air cap at 14 SCFM. The difference is fluid orifice: 1.5mm vs 1.8mm. The 1.5mm suits medium-to-heavy materials in the 21–30 sec. Zahn #2 range. The 1.8mm is better for thicker adhesives and high solid coatings over 30 sec. If your material is on the borderline, call or text CET at 586-210-0555 — we’ll help confirm the right orifice before you order.

What is the difference between the P100G-15-2263 and P100G-15-2266-3T?

Both are 1.5mm pressure setups. The 21-2263 runs at 14 SCFM with a standard aluminum air cap and a 14" max fan. The 21-2266-3T runs at 16.2 SCFM with a PTFE coated air cap and a wider 15" fan. CET recommends the 2266-3T when the PTFE coating for adhesive cleanup is a priority; the 2263 is an excellent all-round pressure configuration for medium-to-heavy adhesives and coatings.

What materials work best with a 1.5mm fluid nozzle?

The 1.5mm orifice handles medium-to-heavy viscosity materials in the 21–30 sec. Zahn #2 range — contact cements, urethane adhesives, automotive base coats, epoxy primers, and high solid enamels. For very thin materials, a smaller orifice gives better control. For the thickest adhesives, step up to 1.8mm.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

Can I upgrade to a carbide nozzle for abrasive materials?

The carbide nozzle range for the Panther 100G starts at 1.8mm — the 31-0618V. For abrasive materials at 1.5mm, contact CET’s technical team to discuss options — call or text 586-210-0555.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Use the table below to find the right nozzle and air cap combination for your material, or contact CET for a CET Application Match recommendation.

PRESSURE requires pressurized fluid supply    SIPHON works with standard siphon cup    WATERBORNE anti-shear setup for waterborne adhesives

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

PTFE Coated Durability for Demanding Applications

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap. This matters most when spraying adhesives, contact cements, and other sticky or aggressive coatings that tend to foul standard aluminum gun bodies and air cap faces.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to surfaces, dramatically reducing cleaning time and extending component life.
• All stainless steel fluid passages: Full chemical resistance across solvent-based, waterborne, and aggressive adhesive formulations.
• Heavy duty needle spring: Maintains consistent trigger response and needle return under continuous production use.
• Forged aluminum body: Lightweight and durable — built for all-day production use without fatigue.
• 17 air cap options: From 0.6mm siphon to 2.8mm pressure — one platform covers the full range of coating viscosities.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.