C.A. Technologies Panther 100G — P100G-22-2167 (2.2mm Nozzle, 2167 Air Cap)

The C.A. Technologies Panther 100G P100G-22-2167 is a 2.2mm PTFE coated conventional pressure feed spray gun paired with the 21-2167 air cap — one of C.A. Technologies’ specifically recommended configurations for heavy adhesive applications. At 14.5 SCFM and pressure feed, this setup delivers consistent, controlled flow of ultra-heavy adhesives, high solid industrial coatings, and thick materials that exceed the capacity of standard 1.8mm pressure setups. Used in furniture manufacturing, industrial laminating, and production finishing operations where high-viscosity materials need reliable pressure-fed delivery at volume. The PTFE hard coat on both the gun body and air cap resists material buildup and simplifies cleanup. All stainless steel fluid passages. US made. Call or text 586-210-0555 for setup guidance and availability before you order.

Overview

At a Glance

• Configuration: 2.2mm stainless steel fluid nozzle + 21-2167 pressure air cap — CET Verified Configuration
• Best for: Heavy adhesives, ultra-thick industrial coatings, high solid enamels, and materials over 30 sec. Zahn #2 requiring pressure feed consistency
• Feed type: Pressure feed — steady, high-volume flow for production adhesive and heavy coating applications
• Air consumption: 14.5 SCFM @ 50 PSI max inlet
• Body: PTFE hard coat anodized forged aluminum — resists adhesive and coating buildup for fast cleanup
• Fluid passages: All stainless steel for full chemical resistance
• Fast fulfillment — most in-stock orders ship same day. Call or text 586-210-0555 to verify availability before you order.
• Origin: US Made by C.A. Technologies (Louisville, CO) — distributed by CET for over 20 years

Specifications

Tech Specs

Application

CET Application Match — Best for This Setup

The P100G-22-2167 is the CET Preferred Setup for high-volume, pressure-fed delivery of heavy adhesives and ultra-thick industrial coatings. C.A. Technologies specifically recommends the 21-2167 for adhesive applications where the material viscosity exceeds what a 1.8mm orifice can reliably deliver under pressure. Based on over 20 years supplying industrial finishing equipment, CET’s technical team specifies this configuration for operations running thick contact cements, high-viscosity laminating adhesives, and heavy solid industrial coatings that require consistent pressure feed at a 2.2mm orifice.

The 12" maximum fan width at 14.5 SCFM gives this setup a tighter, more controlled pattern than wider pressure caps — making it well suited for targeted adhesive application on edge banding, panel lamination, and detail work where precise coverage matters more than maximum fan width. For wider coverage at 2.2mm, the P100G-22-2267 offers 15 SCFM and a 15" fan.

• Industrial laminating and edge banding: Tight 12" fan pattern delivers precise adhesive coverage on narrow substrates and edge applications
• High-viscosity contact cements: 2.2mm orifice under pressure flows thick adhesives consistently without restriction or spitting
• Heavy solid industrial coatings: Pressure feed ensures steady flow of ultra-thick materials over 30 sec. Zahn #2 across production runs
• Furniture and millwork production: Used by shops requiring controlled heavy adhesive application on case goods and panel components

Common Questions

Frequently Asked Questions

Why choose the 21-2167 pressure cap over the 21-2467 siphon cap at 2.2mm?

Pressure feed delivers more consistent flow at high viscosity — especially important when spraying thick adhesives and high solid coatings that require steady material delivery at volume. The 21-2167 at 14.5 SCFM is the CET-recommended choice for production adhesive operations where flow consistency and repeatability across a full tank run matter more than setup portability.

What is the difference between the P100G-22-2167 and P100G-22-2267?

Both are 2.2mm pressure feed configurations. The P100G-22-2167 uses the 21-2167 air cap at 14.5 SCFM with a 12" maximum fan — tighter and more controlled. The P100G-22-2267 uses the 21-2267 at 15 SCFM with a 15" fan — wider coverage for larger substrate areas. CET recommends the 2167 for targeted adhesive work and the 2267 for broader production coating runs. Not sure which fits your application? Call or text 586-210-0555.

When should I choose 2.2mm over 1.8mm for pressure feed adhesive work?

Step up to 2.2mm when your adhesive or coating consistently runs over 30 seconds Zahn #2 and you’re seeing restricted flow, inconsistent atomization, or frequent tip clearing with a 1.8mm setup. The 2.2mm orifice passes significantly more material per trigger pull and handles ultra-heavy body formulations reliably under pressure.

What repair kit does the Panther 100G use?

All Panther 100G configurations use repair kit 10-110, which includes all wear seals, o-rings, springs, and needle seal components for a complete rebuild. Call or text 586-210-0555 to confirm availability for same-day shipment.

Is a carbide nozzle available at 2.2mm for abrasive materials?

Yes — the 31-0622V carbide nozzle is a drop-in replacement for the standard 2.2mm stainless nozzle and significantly extends service life when spraying abrasive or particle-laden heavy coatings. CET’s team can advise on whether carbide is warranted for your application.

Where can I find the full Panther 100G parts manual?

The full parts manual with exploded diagram, parts list, and air cap chart is available on the Panther P100G Spare Parts page or via the download button below. CET includes documentation with every order.

All Configurations

Find the Right Panther 100G for Your Application

The Panther 100G is available in 19 configurations across siphon, pressure, and waterborne adhesive setups. All configurations are CET Verified — supported by CET’s technical team and fulfilled through C.A. Technologies’ Colorado facility. Use the table below to find the right nozzle and air cap combination for your material, or contact CET for a CET Application Match recommendation.

Why Buy From CET

The CET Difference

Why Choose the Panther 100G

PTFE Coated Durability for Demanding Applications

The Panther 100G is the only gun in the C.A. Technologies conventional lineup with a PTFE hard coat on both the gun body and air cap. This matters most when spraying adhesives, contact cements, and other sticky or aggressive coatings that tend to foul standard aluminum gun bodies and air cap faces.

• PTFE hard coat body & air cap: Prevents adhesive from bonding to surfaces, dramatically reducing cleaning time and extending component life.
• All stainless steel fluid passages: Full chemical resistance across solvent-based, waterborne, and aggressive adhesive formulations.
• Heavy duty needle spring: Maintains consistent trigger response and needle return under continuous production use.
• Forged aluminum body: Lightweight and durable — built for all-day production use without fatigue.
• 17 air cap options: From 0.6mm siphon to 2.8mm pressure — one platform covers the full range of coating viscosities.

Outfits & Configurations

Available Outfits

Need Help Selecting the Right Configuration?

Contact CET’s technical support team with your material type, viscosity, and feed preference. Based on over 20 years of industrial finishing equipment experience, we’ll confirm the correct Panther 100G nozzle and air cap combination and verify same-day availability. Call or text 586-210-0555.