Description
C.A. Technologies · Automatic Air Assist Airless · Authorized Distributor
Bobcat Automatic
AB513 · 0.013” Tip · 50° · 10” Pattern
Automatic Air Assist Airless · Machine-Mount · All-Stainless · US Made
| Speccing an automatic finishing line? CET’s technical team will confirm the right Auto Bobcat tip and recirculation setup for your coating before you order. | 586-210-0555 sales@cetinc.com |
|
Overview Automatic.
|
Why This Configuration? The Right Automatic
|
Configuration Detail
AB513 — At a Glance
|
Fluid Tip 36-513 0.013” orifice · 50° angle · ~10” pattern. AAA carbide, field-replaceable; tuned for medium-viscosity production coatings. |
Air Cap AAA HVLP air cap Refines airless atomization with a small volume of HVLP air for a soft, fine break-up on production finishes. |
Gun Type AAA · Automatic Machine-mount · 2500 PSI max All-stainless fluid section, pneumatically actuated. Requires an AAA pump (e.g., Peak 14:1). |
Recirculating or Non-Recirculating
Every Auto Bobcat ships ready for either plumbing. For fluid recirculation through the head, both manifold ports carry fluid inlet 66-253 and fluid can enter from either side. For a non-recirculating (dead-end) setup, one port is blanked with 66-253-B and fluid enters the open side. The gun circulates very close to the tip to keep material from settling.
Other 50° Automatic Configurations
| Model | Tip | Orifice | Angle | Pattern | Best For |
|---|---|---|---|---|---|
| AB509 | 36-509 | 0.009” | 50° | 10” | Thin sealers, stains, and very fine topcoats |
| AB511 | 36-511 | 0.011” | 50° | 10” | Fine lacquers, enamels, and waterborne topcoats |
| AB513 ← Current | 36-513 | 0.013” | 50° | 10” | Medium-viscosity production coatings |
| AB515 | 36-515 | 0.015” | 50° | 10” | Primers, sealers, and higher-output finishing |
| AB517 | 36-517 | 0.017” | 50° | 10” | Heavy primers and high-solid coatings |
|
Technical Data Key Specifications
|
Application Match CET Application Guide
|
All Automatic Configurations
The Bobcat Automatic Line-Up
All 27 Bobcat Automatic configurations are CET Verified. Click any model for its full spec page.
| Model | Tip | Orifice | Angle | Pattern | Best For |
|---|---|---|---|---|---|
| 20° — 4” Pattern | |||||
| AB211 | 36-211 | 0.011” | 20° | 4” | Fine lacquers, enamels, and waterborne topcoats |
| AB213 | 36-213 | 0.013” | 20° | 4” | Medium-viscosity production coatings |
| 30° — 6” Pattern | |||||
| AB309 | 36-309 | 0.009” | 30° | 6” | Thin sealers, stains, and very fine topcoats |
| AB311 | 36-311 | 0.011” | 30° | 6” | Fine lacquers, enamels, and waterborne topcoats |
| AB313 | 36-313 | 0.013” | 30° | 6” | Medium-viscosity production coatings |
| AB315 | 36-315 | 0.015” | 30° | 6” | Primers, sealers, and higher-output finishing |
| 40° — 8” Pattern | |||||
| AB409 | 36-409 | 0.009” | 40° | 8” | Thin sealers, stains, and very fine topcoats |
| AB411 | 36-411 | 0.011” | 40° | 8” | Fine lacquers, enamels, and waterborne topcoats |
| AB413 | 36-413 | 0.013” | 40° | 8” | Medium-viscosity production coatings |
| AB415 | 36-415 | 0.015” | 40° | 8” | Primers, sealers, and higher-output finishing |
| 50° — 10” Pattern | |||||
| AB509 | 36-509 | 0.009” | 50° | 10” | Thin sealers, stains, and very fine topcoats |
| AB511 | 36-511 | 0.011” | 50° | 10” | Fine lacquers, enamels, and waterborne topcoats |
| AB513 ← Current | 36-513 | 0.013” | 50° | 10” | Medium-viscosity production coatings |
| AB515 | 36-515 | 0.015” | 50° | 10” | Primers, sealers, and higher-output finishing |
| AB517 | 36-517 | 0.017” | 50° | 10” | Heavy primers and high-solid coatings |
| 60° — 12” Pattern | |||||
| AB611 | 36-611 | 0.011” | 60° | 12” | Fine lacquers, enamels, and waterborne topcoats |
| AB613 | 36-613 | 0.013” | 60° | 12” | Medium-viscosity production coatings |
| AB615 | 36-615 | 0.015” | 60° | 12” | Primers, sealers, and higher-output finishing |
| AB617 | 36-617 | 0.017” | 60° | 12” | Heavy primers and high-solid coatings |
| AB619 | 36-619 | 0.019” | 60° | 12” | Very heavy materials at high volume |
| AB621 | 36-621 | 0.021” | 60° | 12” | The thickest materials at maximum output |
| 70° — 14” Pattern | |||||
| AB711 | 36-711 | 0.011” | 70° | 14” | Fine lacquers, enamels, and waterborne topcoats |
| AB713 | 36-713 | 0.013” | 70° | 14” | Medium-viscosity production coatings |
| AB715 | 36-715 | 0.015” | 70° | 14” | Primers, sealers, and higher-output finishing |
| AB717 | 36-717 | 0.017” | 70° | 14” | Heavy primers and high-solid coatings |
| 80° — 16” Pattern | |||||
| AB815 | 36-815 | 0.015” | 80° | 16” | Primers, sealers, and higher-output finishing |
| AB821 | 36-821 | 0.021” | 80° | 16” | The thickest materials at maximum output |
Common Questions
Frequently Asked Questions
How is the automatic different from the hand-held Bobcat? The Bobcat Automatic is machine-mounted and pneumatically actuated for reciprocators, flat-line, and robotic finishing — no trigger. It runs at up to 2500 PSI fluid and mounts as a direct replacement for common competitor automatic guns with virtually no hardware change. |
Can it recirculate fluid? Yes. Every gun ships able to run recirculating (both ports fitted with 66-253) or non-recirculating (one port blanked with 66-253-B). It circulates close to the tip to keep material from settling. Standard or Cefla (pivot-hub) manifold available. |
What tip does the AB513 use? The 36-513 AAA carbide tip — 0.013” orifice, 50° angle, ~10” pattern — delivering approximately 17 oz/min at 1000 PSI. Tips are field-replaceable; ask CET about other angles and orifices. |
Bobcat Automatic — Parts & ManualExploded diagram, tip flow chart, maintenance procedures & every replacement part number. |
Parts & Manual → |
Not sure the AB513 is the right automatic setup for your line? Contact CET’s technical team with your material type, viscosity, and mounting — we’ll confirm the right Auto Bobcat tip and manifold before you order. See all Bobcat Automatic spray guns. — 586-210-0555 · sales@cetinc.com
